product structure silicon monolithic integrated circuit radiation resistance design is not arranged 1/66 tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 14 ? 001 datashee t usb audio decoder lsi series aac/wma/mp3 +sd memory card + ipod bu94601kv bu946 03kv bu94604bkv description bu94601kv / bu94603kv / bu94604bkv are aac+ wma + mp3 decoder ic which contains usb host, sd card i/f, audio dac, system controller, and regulator for internal core power supply. features ? usb2.0 full speed host i/f function contained. ? protocol conversion from i 2 c to usb hid or from usb hid to i 2 c. (only bu94604bkv) ? sd card i/f function contained. ? i 2 c i/f function contained. ? fat analysis function contained. ? mp3 decode function contained. (available for mpeg1, 2 and 2.5, layer 1, 2 and 3) ? wma decode function contained. (except bu94601kv) available for wma9 standard and not available for drm ? aac decode function contained. (except bu94601kv) available for mpeg4 aac-lc and not available for drm ? sample rate converter contained. ? system controller contained. ? led controller contained. ? key matrix controller contained. ? stand alone mode contained. ? external processor can control. (slave mode) ? audio dac contained. ? sound effect function contained. ? digital audio output(i 2 s, s/pdif) function contained. ? file name, folder name sorting. ? id3tag and wmatag and aactag analysis. ? reading a specified file data is possible from usb memory. ? lun is selectable. ? regulator for internal core power supply contained. ? vqfp64pin(0.5mm pitch) applications audio products, etc package w(typ.) x d(typ.) x h(max.) vqfp64 12.00mm x 12.00mm x 1.60mm line up part number format ipod package ordering part number bu94601kv mp3 not supported vqfp64 reel of 2000 bu94601kv-zae2 bu94603kv aac/wma/mp3 vqfp64 reel of 2000 bu94603kv-zae2 bu94604bkv aac/wma/mp3 supported vqfp64 reel of 2000 bu94604bkv-zae2 downloaded from: http:///
2/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 basic circuit application diagram-part1 figure 2. an example of connection circuit application (bu94601kv/bu94603kv mode2/3) * figure 1. an example of connec tion circuit application (bu9460 1kv/bu94603kv/bu946 04bkv mode1) * downloaded from: http:///
3/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 basic circuit application diagram-part2 this lsi has built in regulator for internal core power supply. dvdd terminal of 27pin and 57pin connect to bypass condenser. dvdd terminal of 27pin and 57pin dont connect to power supply. the reference circuit and reference circuit parameters for crystal oscillator are shown above. the circuit parameters introduced above is not taking into considerat ion the environment in customers systems or sets board. therefore, rohm is no t guaranteed this content in any circuits. please check the optimal circuit parameter in customers actual systems or produc ts with the oscillator manufacturer. figure 3. an example of connection circ uit application (bu9 4604bkv mode2/3) * downloaded from: http:///
4/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 difference of bu94601kv/bu94603kv/bu94604bkv features item bu94601kv bu94603kv bu94604bkv package vqfp64 number of pins 64pin power supply 3.3v (inner 1.5v regulator ) usb host i/f usb full speed(12mbps) usb mass storage class sd card i/f spi mode sd, sdhc, mmc, mini-sdcard i 2 c command i/f(slave supported audio line output supported digital audio output i 2 s spdif sample rate converter supported clock 16.9344mhz playable mp3 files *.mp3,*.mp2,*.mp1 playable wma files not supported *.asf,*.wma playable aac files not supported *.m4a,*.3gp,*.mp4 ipod not supported supported*1 *1 for using of bu94604bkv, it is necessary to become a licensee of apple inc. regarding "made for ipod/iphone/ipad license". downloaded from: http:///
5/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 block diagram usb i/f sd i/f mp3/wma/ aac decoder * data buffer src i 2 s out spdif out tag analysis system controller command i/f (i 2 c) usb/ system pll 1.5v ldo i 2 s out spdif out audio dac mcu power amp _ file system (fat16/32) 16.9344 mhz 3.3v *bu94601kv contains only mp3 decoder figure 4. block diagram downloaded from: http:///
6/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 arrangement of terminals bu94601kv / bu94603kv / bu94604bkv figure 5. arrangement of terminals downloaded from: http:///
7/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 description of terminals stand alone mode (mode1) slave mode (mode2,mode3) pin no. signal name i/o cir i/o pull-up/ down ( *7 ) function signal name i/o pull-up/ down ( *7 ) function 1 resetx a i pu h: release reset, l: reset 2 sel_slave b i pu(*1) h: stand alone, l:slave 3 sel_mp3 b i pu(*1) h: play mp3 only, l: play mp1,mp2 and mp3 4 sel_dout b i pu(*1) h: audio line output, l: di g ital audio output 5 sel_vol b i pu(*1) h: volume control valid, l: volume control invalid 6 sel_aplay b i pu(*1) h: auto play off , l: auto pla y 7 sel_utpkt b i pu(*1) h: normal operation l: usb test packet output 8 test1 (*2) b o - open (for test) irpto (*3) b o - device (have 2 configuration or more) connections interruption output terminal 9 test2 - i pu pull-up to 3.3v system power suppl y ( for test ) 10 key_row1 b i pu key input row1 mchng o - music change output 11 key_row2 b i pu key input row2 busy o - command operation bus y fla g 12 key_row3 b i pu key input row3 scl i - i 2 c i/f clock input 13 key_row4 b i pu key input row4 sda i/o - i 2 c i/f data input/output 14 key_col1 b o - key input column1 a0 i - i 2 c i/f slave address set0 15 key_col2 b o - key input column2 a1 i - i 2 c i/f slave address set1 16 key_col3 b o - key input column3 sel_sman i pu(*1) h: mode2, l: mode3 17 test3 b i pu pull-up to 3.3v system power suppl y ( for test ) 18 dvddio - - - connect to 3.3v s y stem power suppl y 19 sd_con b i - sd i/f (*4) 20 sd_do b i - sd i/f (*4) 21 sd_clk b o - sd i/f 22 sd_di b o - sd i/f 23 sd_cs b o - sd i/f 24 dvss - - - connect to gnd 25 test4 - i pu pull-up to 3.3v system power suppl y ( for test ) 26 test5 - i pu pull-up to 3.3v system power supply (for test) clkout12(*5) i/o (*5) pu(*5) 12mhz clk output. 27 dvdd_m2 - - - connect to 57pin 28 test6 - i - pull-up to 3.3v system power suppl y ( for test ) 29 test7 - i - pull-up to 3.3v system power suppl y ( for test ) 30 test8 - i - pull-up to 3.3v system power suppl y ( for test ) 31 atest1 - o - open (for test) 32 avddc - - - connect to 3.3v s y stem power suppl y 33 usb_dm c i/o - usb data- 34 usb_dp c i/o - usb data+ 35 avssc - - - connect to gnd 36 rexti d o - usb bias resistor(12k ? ) connecting terminal. arrange the resistance of 12k ? near pin, and wiring on the pin side doesnt cross with other si g nal lines. downloaded from: http:///
8/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 37 vorefi - o - open (for test) 38 vdd_pll - - - connect to 3.3v s y stem power suppl y 39 test_pll - i - open (for test) 40 xin_pll e i - x'tal input 16.9344mhz 41 xout_pll e o - connect to x'tal 16.9344mhz 42 vss_pll - - - connect to gnd 43 davss - - - connect to gnd 44 rdaco f o - audio dac line output rch 45 vcdaco i o - audio dac reference volta g e output 46 ldaco f o - audio dac line output lch 47 davdd - - - connect to 3.3v s y stem power suppl y 48 amute g o - audio mute output ( h:mute cancel, l:mute ) 49 led_error b o - error led output test9 i pu pull-up to 3.3v system power suppl y 50 led_play b o - play led output test10 i pu pull-up to 3.3v system power suppl y 51 led_psd b o - play sd card led output test11 i pu pull-up to 3.3v system power suppl y 52 led_pusb b o - play usb led output test12 i pu pull-up to 3.3v system power suppl y 53 led_access b o - memory access led output lrck /spdif(*4) i/o (*6) pu(*6) i 2 s output lr clock / spdif output 54 led_random b o - random play led output bck(*4) i/o ( *6 ) pu(*6) i 2 s output bit clock 55 led_repeat b o - repeat play led output data(*4) i/o ( *6 ) pu(*6) i 2 s output lr data 56 test13 - i pu pull-up to 3.3v system power suppl y ( for test ) 57 dvdd_m1 - - - connect to b y pass condense r 58 test14 f i - connect to gnd 59 test15 - i - pull-up to 3.3v system power suppl y ( for test ) 60 test16 - i - pull-up to 3.3v system power suppl y ( for test ) 61 test17 - i - pull-up to 3.3v system power suppl y ( for test ) 62 dvss - - - connect to gnd 63 tmode h i - connect to gnd 64 dvddio - - - connect to 3.3v s y stem power suppl y *1 when l is input, pull-up turns off. *2 bu94601kv / bu94603kv *3 bu94604bkv *4 when sd i/f is disused, pull-up to 3.3v system power supply. *5 enabled/disabled can be selected using commands. this pin becomes output and pull-up is off, only when 12mhz clock output is enable. *6 in stand alone mode (mode1), when audio line output is selected (sel_dout=h), led output is enabled. when the digital audio output is selected (sel_dout=l), the i 2 s format audio output is enabled. in slave mode (mode2, mode3), when the analog line output is selected ( sel_dout=h), these pins are test terminals. when the digital audio output is selected (sel_dout=l), i 2 s or spdif is selectable. see chapter 4 . sel_dout for further information. *7 input l level directly without resistance when you input l to the terminal with pull-up (about 33 k ? ). downloaded from: http:///
9/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 terminal equivalent circuit diagram a b c d e f g h i _ _ _ _ downloaded from: http:///
10/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 description of each blocks movement-part1 bu94601kv/bu94603kv/bu 94604bkv are aac+wma+mp3 decoder ic in which a usb host i/f, sd memory card i/f, audio dac and system control functions are built. using a key or i 2 c interface command, the ic reads out a mp3 file written to a memory device having a usb i/f or a sd memo ry card. all the operations required before the data can be output to audio devices are incorporated in to one chip. *bu94601kv supports only mp3. supporting stand alone mode which is enabled by comm ands entered from the keyboard (hereinafter referred to as mode1), auto slave mode which is enabled by comm ands entered from the master microcomputer, same as those entered from the keyboard, via the built-in i 2 c interface (hereinafter referred to as mode2) and manual slave mode which can send the memory device informa tion to the master microcomputer via the i 2 c interface and completely control sequences such as a play sequence by the master microcomputer (hereinafter referred to as mode3). i 2 c bus <-> usb protocol conversion function bu ilt into. *only mode2 and mode3 of bu94604bkv. supporting fast forward playing and fast backward playing with music. supporting outputs folder names, file names, id3tag (v 1.0, v1.1 v2.2 v2.3 and v2 .4) information and wma-tag information and aac-tag(itunes meta-data) information via the i 2 c interface. this function is enabled only in mode 2 and mode 3. supporting audio line output, digital audio output (i 2 s, spdif). reading a specified file data is possible from usb memory. *only a file that exists in root folder corresponds. 1. usb host i/f builds in the usb full speed (12 mbps) host control function. supports the usb mass storage class. convert the protocol from i 2 c from usb(hid) and usb(hid) to i 2 c when communicating with the master microcomputer.* an isochronous in transfer function to 192 byte/frame is built into.* . interrupt in transfer function is built into.* . it doesn't correspond to external hub. * only the device with two configurations or more. only bu94604bkv. 2. sd card i/f supports the spi mode. supports the mmc and mini-sd cards. supports the sdhc cards. supports the sd ver1.01 (file system). does not support cprm. 3. i 2 c i/f communicates with the master microcomputer using an i 2 c interface format. supports the standard mode (100 kbps) and fast mode (400 kbps). supports a 7-bit address. can select four types of slave addresses. 4. audio output 1bit-dac output builds in the digital soft mute function. supports digital audio output (i 2 s, spdif). builds in sound effects of pops, jazz, rock, classic, r&b and bassboost.* * only audio line output is enabled. downloaded from: http:///
11/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 description of each blocks movement-part2 5. fat analysis supports fat16 and fat 32. supports vfat (long file name). supports multi-partition up to 1. the maximum number of playable folders within each folder is 65534. the maximum number of playable files within each folder is 65534. the maximum number of playable folders within each device is 65534. the playable folder hierarchy is up to 8 layers containing the root directory. the playable file extension supports *.m4a, *.3gp, and *.mp4 for aac, *.wma and *.as f for wma, *.mp3, *.mp2, and *.mp1 for mp3. for *.mp2 and *.mp1, play enable d/disabled can be selected. upper case letters and lower case letters are not distinguished in the file extension. (bu94601 kv supports only *.mp3, *.mp2, and *.mp1.) sorts and plays up to 100 folders and 100 files in the order of unicode. possible to obtain up to 64 bytes as the folder name or file name. supports 1 sector of 512, 1024, 2048 and 4096 bytes. playable file size is up to 2gbyte-1 byte. although a file over 2gbyte is recognized as a playable file, 2gbyte -1byte part of the file is playable. 6. mp3 decoder supports mpeg audio 1, 2 and 2.5. supports layer 1, 2 and 3. supports sample rates 8k, 16k, 32k, 11.025k, 22.05k, 44.1k, 12k, 24k and 48khz. supports bit rate 8 to 320 kbps and vbr (v ariable bit rate). *except free format. supports id3tag v1.0, v1.1, v2.2, v2.3 and v2.4. (up to 64 bytes can be obtained for the names of album, artist, and title.) 7. wma decoder (bu94601kv doesnt support.) supports windows media audio 9 standard. not supports drm. supports sample rates 8k, 16k, 32k, 11.025k, 22.05k, 44.1k, and 48khz. supports bit rate 5 to 384 kbps and vbr (v ariable bit rate). *except free format. supports wma-tag. (up to 64 bytes can be obtained for the names of album, artist, and title.) 8. aac decoder (bu94601kv doesnt support.) supports mpeg4 aac-lc encoded by itunes. not supports drm. supports sample rates 8k, 16k, 32k, 11.025k, 22.05k, 44.1k, 12k, 24k and 48khz. supports bit rate 8 to 320 kbps and vbr (variable bit rate). supports aac-tag(itunes meta-data). (up to 64 bytes can be obtained for the names of album, artist, and title.) the playable file extension su pports *.m4a, *.3gp, and *.mp4 based on 3gpp ts 26.244. supports file type of m4a, mp42, and 3gpx (numbers with arbitrary x). *about except for the file encoded by itunes, when the stream of a gap or video data is included in the file, it may skip to the following music or skipping may be carried out. 9. sample rate converter converts all the supported sample rates to 44.1 khz using a poly-phase operation. 10. system controller controls all the system operations including key input, le d output, interface control with the master microcomputer, usb device access, sd card access, fat analysis, so rt function, mp3 decode, wma decode and audio output. downloaded from: http:///
12/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 description of each blocks movement-part3 11. key matrix controller controls 12 types of key inputs: play/pause, stop, tune fo rward/fast forward playing, tune backward/fast backward playing, folder forward, folder backward, 10-tune forward, volume up, volume down, repeat play, random play and device selection. 12. led controller controls 7 types of led outputs: play/pause, error, me mory accessing, random playing, repeat playing, usb selection and sd selection 13. control from the master microcomputer control from the master microcomputer is enabled using the i 2 c interface. through the command operations, the following can be contro lled: play, pause, stop, t une forward, tune backward, fast forward playing, fast backward playing, folder fo rward, folder backward, 10-tune forward, 10-tune backward, volume up, volume down, device selection, volume setting, r epeat selection, random play, digital audio output setting, sound effect setting, resume data setting and direct tune selection data setting. controls the following: playing status out put, pause, stop, searching, error, folder number, file number within folder, play time information, number of total folders, number of to tal files, name of folder bei ng played, name of file being played, id3tag (title, artist and album) , wmatag (title, artist and album), aactag (title, artist and album),resume data and direct tune selection data (mode3). 14. function selection selects mode1 or mode2/3 (se l_slave=h: mode1, l: mode2/3). selects mpeg audio layer (sel_mp3=h: play mp3 only, l: play mp1/mp2/mp3) digital audio output selection (se l_dout=h: output off, l: output on) sound volume operation selection (sel_vol=h: volume adjustable, l: volume not adjustable max output) selects operation at power on to check device (sel_a play=h: stop, l: play). *enabled in mode 1 only. selects mode2 or mode3 (sel_sman=h: mode2, l: mode3). *enabled in mode 2/3 only. 15. file read function in usb memory the specified data of file that exists in the root folder of the usb memory reading is possible. * the file name corresponds only by 8. 3 forms. (the wild-card cannot be used.) downloaded from: http:///
13/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 absolute maximum ratings (ta = 25 ) parameter symbol limits unit comment supply voltage(analog, i/o) vdd1ma x -0.3 to 4.5 v dvddio, vdd_pll, davdd, avddc input voltage vin -0.3 to vdd1 + 0.3 v storage temperature range tstg -55 to 125 operating temperature range topr -40 to 85 power dissipation *1 pd 750 mw *1 in the case of use at ta=25 or more, 7.5mw should be reduced per 1 . radiation resistance design is not arranged. operating conditions (ta = 25 ) parameter symbol limits unit comment supply voltage(analog, i/o) vdd1 3.0 to 3.6 v dvddio,vdd_pll, davdd, avddc electrical characteristics (unless specified, ta=25 ,vdd1=3.3v, dvss=avssc=vss_pll= davss=0v, xin_pll=16.9344mhz parameter symbol limits unit condition min. typ. max. circuit current (vdd1 usb1) idd1usb1 - 65 80 ma *1 when usb memory is played. circuit current (vdd1 sd1) idd1sd1 - 35 50 ma *1 when sd card is played. h-level input voltage vih vdd1*0.7 vdd1 v *3 l-level input voltage vil dvss vdd1*0.3 v *3 h-level output voltage1 voh1 vdd1-0.4 vdd1 v ioh=-1.6ma, *4 l-level output voltage1 vol1 0 0.4 v iol=1.6ma. *4 h-level output voltage2 voh2 vdd1-0.4 vdd1 v ioh=-3.6ma, *5 l-level output voltage2 vol2 0 0.4 v iol=3.6ma, *5 h-level output voltage3 voh3 vdd1-0.4 vdd1 v ioh=-0.6ma, *6 l-level output voltage3 vol3 0 0.4 v iol=0.6ma, *6 h-level output voltage4 voh4 vdd1-1.0 vdd1 v ioh=-0.6ma, *7 l-level output voltage4 vol4 0 1.0 v iol=0.6ma, *7 h-level input voltage vihusb vdd1*0.6 vdd1 v *8 l-level input voltage vilusb avssc vdd1*0.3 v *8 output impedance(h) zoh 22.0 45.0 60.0 ? *8 output impedance(l) zol 22.0 45.0 60.0 ? *8 h-level output voltage vohusb vdd1-0.5 vdd1 v *8 l-level output voltage volusb 0 0.3 v *8 rise/fall time tr/tf 11 ns *8, output capacity 50pf voltage of crossing point vcrs vdd1/2 v *8, output capacity 50pf range of differential input vdiff 0.8 2.5 v *8 differential input sensitivity vsens 0.2 v *8 pull-down resistance rpd 14.25 15.0 24.8 k ? *8 distortion rate thd 0.02 % 1khz, 0db, sine, *9 dynamic range dr 88 db 1khz, -60db, sine, *9 s/n ratio s/n 96 db *9 max output level vsmax 0.92 vrms 1khz, 0db, sine, no load, *9 *1 3.3v system i/o, analog power supply(vdd1), 1khz, 0db, sine-wave playing *3 1-7, 9-17, 19-20, 25-26, 28-30, 40, 49-52, 56, 58-61, 63 pin *4 8, 10-11, 14-16, 48-55 pin *5 13 pin *6 21-23, 26 pin *7 41 pin *8 33, 34 pin *9 44, 46 pin downloaded from: http:///
14/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 application information 1. clock and reset clock signal name i/o function remarks xin_pll i xtal (16.9344 mhz) connection input terminal xout_pll o xtal (16.9344 mhz) connection terminal reset signal name i/o function remarks resetx i system reset input terminal to disable a reset signal, continue l input for more than 5 us after all of the supply voltage reach the specified value and clock input from the oscillation i/o te rminal becomes stable. (see figure 6.) figure 6 reset timing item symbol specification unit remarks min typ max clock frequency f clk 16.9302 16.9344 16.9386 mhz reset l interval t rstx 5 - - us 2. sel_slave mode1/mode2, 3 selection input signal signal name i/o function remarks sel_slave i selects mode1 or mode 2, 3. h: mode1, l: mode2, 3 sel_slave selects mode1 (stand alone mode) or mode 2/3 (slave mode). by selecting sel_slave, slave mode terminal setting is enabled. sel_slave is set only at power on. note that change of selection after power on is ignored. 3. sel_mp3 mpeg audio layer 1, 2, 3 play selection signal signal name i/o function remarks sel_mp3 i mpeg audio layer selection h: can play mp3 only.l: can play mp1, mp2 and mp3. sel_mp3 allows you to select the la yer of the mpeg audio to be played. when enabling all the files having mp1, mp2 or mp3 as the file extension to be played , enter l. when enabling mp3 only, enter h. sel_mp3 is set only at power on. note that change of election after power on is ignored. _ downloaded from: http:///
15/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 4. sel_dout audio output selection signal signal name i/o function remarks sel_dout i audio output selection h: line output, l: digital output(i 2 s, spdif) this sel_dout selects audio output signal. table 1. audio output shows the audio outputs for each mode. also table 2. i 2 s_fs shows the i 2 s output formats for each mode. for command, see chapter vii "test terminal" needs to be pull-up to 3.3v power supply. table 1. audio output _ _ _ ??? _= _= _= _= table 2. i 2 s_fs mode1 32fs mode2/3 can select 32fs, 48fs, 64fs by command. sel_dout is set only at power on. note that c hange of selection after power on is ignored. 5. sel_vol sound volume operation selection signal signal name i/o function remarks sel_vol i sound volume operation h: sound volume operation enabled, l: sound volume operation disabled sel_vol selects whether sound volume operation is to be enabled or disabled. sound volume operation is enabled when sel_vol=h. initial value of audio output is -24.1db at power on. sound volume operation is disabled when sel_vol=l. audio output is fixed to 0db. figure 7 shows the relationship between audio output and sound volume step. sel_vol is set only at power on. note that change of selection after power on is ignored. figure 7 volume step function volume ste p initial value: -24.1 db (when sel_vol=h) - audio output (db) downloaded from: http:///
16/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 6. sel_aplay auto play selection signal at power on/device recognition signal name i/o function remarks sel_aplay i auto play selection signal at device reco g nition h: stop after recognizing device, l: play after reco g nizin g device sel_aplay selects whether the audio data in the memory is to be automatically played when a memory device (usb memory or sd card) is inserted at power on or when the system recognizes the memory device inserted. sel_aplay can be selected only in mode1. since select ion of sel_aplay is ignored in mode2/3, select it from pull-up. when mode2/3 is selected, audio data is halted after the system recognizes a device. 7. sel_utpkt usb test packet signal name i/o function remarks sel_utpkt i usb test packet send h: disabled, l: usb test packet send a test packet signal is output from usb_dp terminal or usb_dm terminal when l is set to sel_utpkt at power on. once enabled, sel_utpk keeps that state regardless of operation modes and sends out a test packet. a test packet signal is continuously output until powe r turns off. use sel_utpkt when evaluating the usb terminal. in other cases, use it from pull-up. 8. audio line output audio line output signal name i/o function remarks ldaco o lch audio line output - rdaco o rch audio line output - these signals are decoded mp3 music audio data line outputs. they turn on when the line output is selected by sel_dout terminal. sample rate converter converts the sample ra te 48khz and 32khz to 44.1khz and outputted. 9. mute control output audio mute signal name i/o function remarks amute o audio mute control terminal h: at audio output, l: at mute this terminal outputs h at audio output and l at mute. this signal can be used as flag for external amplifier when mute audio output at power on or ff/fb (silence). figure 8 shows the operation waveform. figure 8 waveform at audio mute ldaco, rdaco amute at start of play at stop of play 23 ms at 0db 23 ms at 0db downloaded from: http:///
17/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 10. key input format 3x4 matrix command input signal name i/o function remarks key_row1 i key matrix i/o signal - key_row2 i - key_row3 i - key_row4 i - key_col1 o - key_col2 o - key_col3 o - configure a circuit for the matrix signals terminals for key commands as shown in the applied circuit diagram figure 9. the operation corresponding to the key pr essed over the circuit is performed. details of each operation are explained in chapter 21. figure 9 key matrix applied circuit diagram 11. i 2 c interface format i 2 c serial interface signal name i/o function remarks scl i i 2 c interface clock input - sda i/o i 2 c interface data i/o - a0 i slave address selection terminal slave address [0] bit setting terminal a1 i slave address selection terminal slave address [1] bit setting terminal this is an i 2 c serial interface terminal. by inputting l to sel_slave terminal, the interface terminal becomes enabled. the terminal supports slave i 2 c operation. 11.1 i 2 c protocol when i 2 c bus is in idle, sda and scl are set to h by the external pull-up resistance. when starting communications, the master sets sda to l while scl is set to h (start condition). when ending communications, the master sets sda to h while scl is set to h (stop condition). during transfer, sda is changed only when scl is set to l. figure 10 shows start condition, stop condition of i 2 c. msb 12 8 lsb ack 9 1 ack 9 sda scl start condition stop condition figure 10 i 2 c start, stop condition _ _ _ _ _ _ _ _ downloaded from: http:///
18/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 11.2 slave address an i 2 c bus slave address corresponds to the 7-bit addressing mode. as shown in table 3., you can select the slave address using input of a0 terminal and a1 terminal . figure 11 shows the slave address transfer format. figure 11 slave address transfer format table 3. settable slave addresses msb a6 a5 a4 a3 a2 a1 terminal lsb a0 terminal 1 0 0 0 0 0 0 1 0 0 0 0 0 1 1 0 0 0 0 1 0 1 0 0 0 0 1 1 11.3 write protocol from master to send a master command using an i 2 c bus, follow the transfer protocol shown in figure 12. for details on each command, see chapter of command operation. figure 12 command send protocol 11.4 read protocol to master to send reception data using an i 2 c bus from the slave to the master, fo llow the transfer protocol shown in figure 13. first, transfer the status read command (step1). then, input scl clock of required bytes in step 2 to read the status. when the device is busy at reception of device status or memory data, the i 2 c bus may possibly be occupied by the device during busy. this lsi transfers the bus to the master so as not to generate such bus occupation. however, as a busy state still exists inside of the system, appropriate data may not be transferred during busy. therefore, the first byte of tr ansfer data (step2) is used to judge the transfer data is enabled/disabled. when specifying addresses from the mast er to the slave and the first byte of the transfer data immediately after data transfer is required is 0x00, tr ansfer data from the slave is enabled. if the first byte is 0xff, it shows the busy state. therefore, the transfer data should be disabled. if this happens, retry command transfer at step 1 to read out the status. figure 14 shows the relationship between the transfer data and busy. * for further information on busy, see chapter 17. s a6 a5 a4 a3 a2 a1 a0 r/w ack start condition slave address sent by slave r / w = read / write pulse ack = acknowledge s slave address a data(8bit) r/w a data(8bit) a data(8bit) p a/a from master to slave from slave to master "0"(write) a = acknowledge(sda low) a = no acknowledge(sda high) s = start condition p = stop condition downloaded from: http:///
19/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 figure 13 status reception protocol figure 14 relationship between transfer data and busy 11.5 i 2 c bus line electrical specification and timing sda and scl bus-line characteristic (unless specified, ta=25 , vdd1=3.3v) parameter code min. max. unit 1 sda, scl h input voltage vih vdd*0.7 vdd v 2 sda, scl l input voltage vil dvss vdd*0.3 v 3 sda h output voltage voh vdd-0.4 vdd v 4 sda l output voltage vol 0 0.4 v 5 scl clock frequency fscl 0 400 khz 6 bus-free-time between "stop" condition and "start" condition tbuf 1.3 us 7 hold time for "start" condition after this, the first clock pulse is generated. thd;sta 0.6 us 8 low status hold-time of scl clock tlow 1.3 us 9 high status hold-time of scl clock thigh 0.6 us 10 data-hold-time thd;dat 0 * us 11 date-setup-time tsu;dat 100 ns 12 rising time of sda and scl signal tr 20+0.1*cb 300 ns 13 fall time of sda and scl signal tf 20+0.1*cb 300 ns 14 setup time of "stop" condition tsu;sto 0.6 us 15 capacitive load of each bus-line cb 400 pf the above-mentioned numerical values are all the values corresponding to v ih min and v il max level. *to exceed an undefined area on falling edged of scl, transmissi on device should internally offer the hold-time of 300ns or mor e for sda signal (v ih min of scl signal). because the "repeated start" condition to send "start" condition without sending "sto p" condition doesn't correspond, after sen ding "start" condition, always send "stop" condition. neither terminal scl nor terminal sda correspond to 5v tolerant. s slave address a data(8bit) r/w a data(8bit) p a/a from master to slave from slave to master "0"(write) a = acknowledge(sda low) a = no acknowledge(sda high) s = start condition p = stop condition step1 s slave address a data(8bit) r/w a data(8bit) p a/a "1"(read) step2 data(8bit) a step1 command s slave address a 0xff a data(8bit) p a/a data(8bit) a r step1 command s slave address a 0x00 a data(8bit) p a/a data(8bit) a r dummy byte for busy dummy byte for busy busy i2c downloaded from: http:///
20/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 figure 15 timing chart 12. i 2 s format i 2 s format signal name i/o function remarks lrck o i 2 s bit clock output (fs=44.1khz) - bck o i 2 s bit clock output - data o i 2 s data output - this is digital audio interface terminal. by inputti ng l to sel_dout terminal, the interface terminal becomes enabled. when selecting the i 2 s digital audio output, the output fo rmat varies depending on mode. mode2 allows you to select 32fs, 48f s or 64fs. *see chapter 4. figures 16, 17 and 18 show the i 2 s format to be output. figure 16 i 2 s output timing (32fs) figure 17 i 2 s output timing (48fs) figure 18 i 2 s output timing (64fs) 12.1 i 2 s timing 48fs i 2 s format (unless specified, ta=25 , vdd1=3.3v, load : 20pf) parameter symbol min typ max unit bck clock frequency tbck - 472.4 - ns bck low time tbck1 216 236 - ns bck high time tbck2 216 236 - ns lrck clock frequency tlrck - 44.1 - khz lrck output delay tlrck1 -20 0 20 ns data output delay tda1 -20 0 20 ns output high voltage voh vdd1-0.4 - - v output low voltage vol - - 0.4 v lrck left channel right channel bck(48fs) data 15 14 12 11 10 9 8 7 6 5 4 3 2 1 0 15 14 13 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1 0 lrck bck(32fs) data left channel 15 right channel 13 12 15 14 11 8 7 10 9 6 3 2 5 4 1 0 13 12 15 14 lrck bck(64fs) data left channel right channel downloaded from: http:///
21/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 tlrck1 msb data bck left channel tbck1 vol lrck tbck2 voh vol tda1 vol figure 19 timing chart 13. spdif format spdif format signal name i/o function remarks spdif o spdif output - spdif output becomes enabled by setting sel_dout terminal to l and setting this condition using the i 2 c command. figure20 shows the spdif digital audio signal output format. figure 20 spdif output format a sub-frame of spdif is composed of synchronous preamble, 16-bit audio data, v bit (validity flag), u bit (user data), c bit (channel status) and p bit (parity bit). output rate is fi xed to 1x speed. spdif outputs synchronous preamble (source code 0-3) as it is and others (source code 4-31) as bi-phase output. it outputs l while the operation is stopped. synchronous preamble and c bit use 32 frames ( 4.4ms) as one cycle. table 4. and table 5 show these formats. v bit is fixed to l. u bit uses 98 frames ( 13.3ms) as one cycle. table 4. synchronous preamble pattern l0 r0 l1 r1 l2 r2 l3 r3 l4 r4 l5 r5 0 b w m w m w m w m w m w 1 m w m w m w m w m w m w : : : : : : : : : : : : : 31 m w m w m w m w m w m w all 0 lsb msb 03 4 1 1 1 2 2 7 2 8 2 9 3 0 3 1 downloaded from: http:///
22/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 table 5. c bit format l0 r0 l1 r1 l2 r2 l3 r3 l4 r4 l5 r5 0 0 0 0 0 0 0 1 0 0 1 0 0 0 2 0 0 0 0 0 0 3 0 0 1 0 0 1 0 0 4 0 0 0 0 0 0 5 0 0 0 0 0 0 : : : : : : : 31 0 0 0 0 0 0 table 6. u bit format l0 r0 l1 r1 l2 r2 l3 r3 l4 r4 l5 r5 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 2 1 0 0 0 0 0 0 0 0 0 0 0 3 1 0 0 0 0 0 0 0 0 0 0 0 : : : : : : : : : : : : : 97 1 0 0 0 0 0 0 0 0 0 0 0 p bit is set to 1 if the number of 1s of source codes 4-30 is odd, and set to 0 if the number is even. therefore, the number of source codes which turn to 1 for one dat a must be an odd value, spdif ends with l output and preamble output always starts in the same direction. 13.1 spdif timing (unless specified, ta=25 , vdd1=3.3v, load : 20pf) parameter symbol min typ max unit spdif clock frequency tck - 2.822 - mhz spdif clock high time tck1 150 177 - ns spdif clock low time tck2 150 177 - output high voltage voh vdd1-0.4 - - v output low voltage vol - - 0.4 v figure 21 timing chart 14. usb i/f usb i/o i/f signal name i/o function remarks usb_dp i/o usb d+i/o terminal - usb_dm i/o usb d-i/o terminal - rexti o usb bias resistance connection terminal connect resistance of 12k ? 1% to gnd. differential signals of usb_dp and usb_dm enable communications with usb devices. rexti terminals become bias resistance connection terminals of the usb-phy block. downloaded from: http:///
23/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 15. sd i/f spi interface for sd memory card i/f signal name i/o function remarks sd_cs o spi chip select - sd_clk o spi clock - sd_di o spi data input - sd_do i spi data output - sd_con i sd card connect detection terminal h: not detecting sd card connection. l: detecting sd card connection. these i/f enable communication with sd memory cards through sd memory card slots. since sd memory card slot requires detecting insertion of sd memory card, use of slot equipped with sd memory card detecting terminal and connection to sd_con terminal are required. sd_con terminal is pulled up within the device and detects sd memory card connection by l input. 15.1 sd i/f timing (unless specified, ta=25 , vdd1=3.3v, load : 20pf,10k ? ) parameter symbol min typ max unit sd_cs setup time tcss - 0.25 - us sd_cs hold time tcsh - 1.15 - us sd_clk clock frequency tclk - 4.23 - mhz sd_di output delay tod -20 - 20 ns sd_do data in setup time tds 20 - - ns sd_do data in hold time tdh 120 - - ns output high voltage voh 0.625*vdd1 - - v output low voltage vol - - 0.25*vdd1 v figure 22 timing chart of spi for sd memory card 16. mchng playing sound tune number detection output signal name i/o function remarks mchng o music tune number change detection output signal h: playing, l: tune completed/stopped this signal outputs change of file to be played during playing mp3 file in the memory device. mchng correctly outputs "h" during mp3 decode sequence, outputs "l" during "stop" status. connect it to the interrupti on port of the microcomputer. downloaded from: http:///
24/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 17. busy busy state detection output signal name i/o function remarks busy o busy state detection output signal h: busy, l: not busy this signal outputs to indicate that this lsi is in busy. busy signal analyzes commands from the mast er and outputs h until the operation is executed. this lsi ignores command input during busy. however, only the abort and stop commands can be accepted even during busy, which can be executed. *see chapter 11. 18. irpto config outputs it for two more dev ice connection state detection. signal name i/o function remarks irpto o usb config outputs it for two more device connection state detection. h: detection , l: undetection. when the usb device is chosen, output it to show that the usb device that two usb configuration descriptor or more has in this lsi is connected. t he timing of an output is dep endent on the connected usb device. 19. test terminal by the terminal setting of test15, test16 and test17, it is possible to following function. test15 test16 test17 function h h h full function effective l l l only wma and mp3 can play-back. the aac file is disregarded. *1 h l l the irpto function is invalidated. *2 *1 except for bu94601kv *2 only bu94604bkv downloaded from: http:///
25/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 20. file detection 20.1 function this function supports fat16 and fat32 file sy stems. (it does not support ntfs and fat12.) the maximum number of playable files per folder table 7. maximum number of playable files root folder sub folder fat16 512 65534 fat32 65535 65534 the number of files described above contains unsupported files and folders. if unsupported files and folders exit within the folder and exceed the maximum number, all the supported files may not be played. files less than 100 can be sorted by unicode in the fat order within the folder. files over 100 are sorted in the fat order. also, the folders can be sorted in the same manner and those over 100 are sorted in the fat order. the searchable folder hierarchy is of 8 layers contai ning the root folder. figure 23 shows an example of memory layers. figure 23 example of memory layers downloaded from: http:///
26/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 20.2 playable file (bu94601kv doesnt support aac/wma files) the playable file extensions are *.m4 a, *.3gp and *.mp4 for aac files, *. wma and *.asf for wma files, *.mp3, *.mp2 and *.mp1 for mp3 files. (upper case letters and lo wer case letters are not distinguished.) note that the file operation differs in the following cases: (1) sel_mp3: see sel_mp3 for details. (2) attribute: aac/wma/mp3 file whose attribute is ma sked can be played. a file with system attributes cannot be played. (3) data destroyed file: when the data section of aac/wma/mp3 file is destroyed, the music data of the file can be played as much as possible rather than disabling to play the entire file. the section which cannot be played is muted. however, amute terminal remains the h output level. when the header section of wma and aac file is destroyed, it plays next. (4) file name: a file name and its size do not depend on playing. (5) extension: when file data is configured in the non- aac format and its file extension is *.m4a, *.3gp and *.mp4 the state is play next. when file data is conf igured in the non-wma format and its file extension is *.wma, or *.asf, the state is pl ay next. when file data is configured in the non-mp3 format and its file extension is *.mp3, *.mp2 or *.mp1, the state is silent playing basically. if playable data can be read, only a part of the file can be played. the information on ti me required to output serial status also becomes uncertain. then, partial output is done but t he correct time information is not output. (6) file size: when file size is 0, the file do not recognize at aac/wma/mp3 files. (7) this lsi corresponds to the aac file encoded by it unes. the versions of itunes checked operation are 4.*, 5.*, 6.*, and 7.0 to 7.5. the aac file encoded with other software may cause fault, such as being in the middle of reproduction and skipping to next. (8) when the extension of wma file is *.asf, this ls i corresponds to the asf file of only an audio stream. 20.3 playing sequence the playing sequence of supported files is dete rmined based on the following rules. see figure24. (1) folders are sorted in the order written in fat (in t he order of fat), and files 1 to 100 are sorted in the order of unicode. (*see chapter 20.4.) f iles over 100 are sorted in the orde r of fat. folders over 100 are sorted in the same manner. files are sorted following sel_mp3. folders are sorted including null folders and those in which supported files are not written. within each folder, supported files over 100 and folders over 100 are played in the order written to the fat directory entry. since how to write to the directory entry depends on t he os (operating system) processing to write to the memory, you cannot understand the file playing sequence. (2) when supported files exist in the root folder (the highest layer), the files are played first. (3) when all the files in the root folder have been played, those in the folder under the root folder, if any, are played. (4) when a folder is layered under that, files in the folder are played. when not, the master searches any other folders at the same layer and plays the one, if any. (5) after playing all the files, the master returns to the root folder as described in (2) and start playing with the first sorted file. 20.4 folder/file sort folders and files are sorted in the following sequence using this lsi. (1) obtain up to 100 files and 100 folders in the order written to fat. (2) compare the obtained folder/file names up to 14 char acters (including filename extensions) and sort them in the ascending order.* (3) when the same strings are generated, follow the order written to fat. (4) for 101 or more folders and files, follow the order written to fat. * the processing of the file name and the folder name is shown in the following. 1)when the lfn(long file name) entry exists, folder/fi lename is processed as one character in two bytes. 2)when the lfn entry doesn't exist, the sfn(short f ile name) entry is processed as follows. 2-a) when character-code that appears first is R 0x80 ,its treated as the first byte of two byte character. byte data afterwards is treated as the second byte of two byte character-code, and treated by two bytes as one character. 2-b) when the case that doesn't apply to 2-a) ,that is, the character-code appears first is installed within the range of 0x00-0x7f(us-ascii) one byte is treated as one character. '0x00' is added and enhanced to unicode. please confirm the spec ification of the fat filesystem about details of lfn and sfn. downloaded from: http:///
27/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 [root folder] a.mp3 b.mp3 c.mp3 a_folder d.mp3 e.mp3 f.mp3 g.mp3 h.mp3 b_foder i.mp3 j.mp3 c_folder k.mp3 l.mp3 m.mp3 n.mp3 o.doc p.xls q.mp3 d_folder r.txt s.txt t.txt e_folder u.mp3 v.mp3 w.mp3 x.mp3 y.mp3 z.mp3 figure 24 configurations of folders and files within memory device table 8. mp3 file playing sequence for folder/file configuration as in figure24 playing sequence file to be pla y ed remarks 1 a.mp3 if mp3 files exist in the root folder, those files are played first. files are played in the ascending order of unicode by file name. 2 b.mp3 3 c.mp3 4 d.mp3 after all mp3 files in the root folder are played, the master searches folders under that layer. the master searches folders in the ascending order of unicode by folder name. 5 e.mp3 6 f.mp3 7 g.mp3 8 h.mp3 9 i.mp3 10 j.mp3 11 k.mp3 12 l.mp3 13 m.mp3 14 n.mp3 15 q.mp3 non-mp3 files are ignored. 16 u.mp3 after the master plays all mp3 files including those in the lower layers within a_folder, it moves to a folder in the same layer as a_folder to search mp3 files. since there is no mp3 file in d_folder, the layers same as a_folder, the master plays mp3 files in e_folder under that. 17 v.mp3 18 w.mp3 19 x.mp3 20 y.mp3 21 z.mp3 downloaded from: http:///
28/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 20.5 search within multi- drive and multi-partition if a device is a multi-drive type or multi partition type, the lsi can recognize the driv e by selecting lun (logical unit number) for the supporting fat. (mode2 and mode3) if particular lun isnt selected, the lsi mount s the device whose lun det ected first. (default) when the multi-card reader is connected, the lsi can recognize device which connected to the card-reader by selecting lun. but after the device is mounted, its impos sible to recognize states whether the device connected to the card-reader is inserted or removed. 20.6 external hub search when the usb connector is connected to a hub, and a fa t-supported drive is conne cted ahead of the hub at mounting the usb for this lsi, only one drive is recognized. the lsi does not support external hubs, it cannot detect plugging/unplugging of the drive ahead of the hub after the usb is mounted. 21. mode1 21.1 key command operation 21.1.1 key scan (single mode) key scan operates in the following sequence on t he circuit configuration as shown in figure 9. (1) key_col1 to 3 output waveforms at timing as shown in figure25. (2) by pressing key switch, key_row 1 to 4 are se t to l at timing when key_col 1 to 3 are l. (3) when detecting l input from key_row 1 to 4 th ree times, the master judges that key has been pressed. then, the master starts the key operation. figure 25 key scan waveform. figure 26 operating waveforms when key is pressed _ _ _ _ _ _ _ _ downloaded from: http:///
29/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 21.1.2 key scan (hold mode) key scan operates in the following sequence on t he circuit configuration as shown in figure 9 . (1) key_col1 to 3 output waveforms at timing as shown in figure25. (2) by pressing key switch, key_row 1 to 4 are se t to l at timing when key_col 1 to 3 are l. (3) when detecting l input from key_row 1 to 4 th ree times, the master judges that key has been pressed. then, the master star ts judging status of held key. (4) when pressed keys decision (l input from key_ro w 1 to 4 three times) is detected consecutive 15 times, the master judges that key mode is hold mode. (5) when key release is detected in judging status of hold key, the master judges that key mode is single mode. then, the master starts the key operation. (6) when hold mode is detected, the master starts the key operation in hold mode. when key release is detected in hold mode, the master finish the key operation. the keys corresponding to hold mode are ff, fb, vol+, and vol-. figure 27 key scan waveform. note 1: based on the above sequence, th e master determines that key is pressed and starts the operation of the pressed key, pressing multiple keys at the same time wi ll produce different operations depending on the key combinations. therefore, you cann ot regulate the operati on sequence correctly even simultaneously pressing multiple keys will not cause any problems. in hold mode, other pressed key is disregarded. note 2: because the key input does not have a buffering function, key inputs other than those described below are ignored. downloaded from: http:///
30/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 21.1.3 key operation table 9. shows the types and operations of keys. table 10. shows enabled/disabled states of key operations. table 9. key commands and operation description key command operation description play/pause when receiving play/pause key during stop, the master starts playing the first mp3 file sorted to the recognized device. when receiving play/pause key during play, the master stops playing the mp3 file temporarily. when receiving play/pause key again, the master restarts playing the file. stop when receiving stop key during play, pause or file search, the master stops playing, pausing or searching the mp3 file. ff when receiving ff key (single mode) during pl ay or pause, the master searches the next supported file in the order of sort of files being played or paused. upon completion of searching, the master starts playing the file. during play of the last file, the master returns to the first file in the order of sort and plays the file. when receiving ff key (hold mode) during play or pause, the master starts fast forward playing the file. when "ff" key release is detected, the master return to normal playing. when music finishes into "ff" key (hold mode), the master starts fast forward playing from top of the next file. however, when selectin g repeat or random, master search next file by setup. fb when receiving fb key (single mode) during play or pause, the master searches the previous supported file in the order of sort of files being played or paused. upon completion of searching, the master starts playing the file. during play of the first file, the master plays the last file in the order of sort. when receiving "fb" key within 1sec from top of file playing, t he master searches the previous supported file in the order of sort of files being played. upon completion of searching, the master starts playing the file. when receiving "fb" key over 1sec from top of file playing, the master starts playing from top of the file. when receiving fb key (hold mode) during play or pause, the master starts fast backward playing the file. when "fb" key releas e is detected, the master return to normal playing. when music finishes into "fb" key (hold mode), the master starts fast backward playing from end of the previous file. however, when selecting repeat or random, master search previous file by setup. fol+ when receiving fol+ key during play or paus e, the master searches the supported files in the next folder in the order of sort of the folder in which the file being played or paused exists. upon completion of search, the master plays the file. during play of the file in the last folder in the order of sort, the master plays the first file in the order of sort. fol- when receiving fol- key during play or paus e, the master searches the supported files in the next folder in the order of sort of the folder in which the file being played or paused exists. upon completion of search, the master plays the file. during play of the file in the first folder in the order of sort, the master plays the first file in the order of sort in the last folder. +10 when receiving +10 key during play or pause, the master searches supported files 10 files next to the current one in the order of so rt of the file being played or paused. upon completion of search, the master starts playing the file. when the remaining files are less than 10 during play of the current file, the master plays the first file. vol+/vol- when receiving vol+/vol- key while sel_vol terminal is set to h, the master controls sound volume. sound volume can be controlled at 32 steps from - (minimum volume) to 0db (maximum volume). since vol+/vol- key does not judge release of key, the master turns up or down volume step by step when determining press of the key. therefore, vol key can be held down. downloaded from: http:///
31/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 chng_dev the master selects the device between usb memory and sd memory card. to do this, both devices should be connected or one device should correspond to the other (usb to sd or sd to usb). otherwise, this key operation is ignored. stop after selecting the device at the top tune of the device. repeat and random settings return to the initial values. when inserting both usb memory and sd memo ry card, or neither usb memory nor sd memory card, the master precedes usb memory. repeat this key changes the mode of repeat. press of repeat key toggles like: repeat all tunes in memory ? repeat one tune ? repeat within folder. when selecting repeat within folder, the master repeats files within the folder being played. the initial setting is repeat all tunes in memory. random this key plays the range of 128 files from the current one being played in the order of sort at random. random key is enabled to change mode only during play, pause or stop. table 10. key operation enabled/disabled after recognizing device (search or pause) during play of device searching error recognize either usb or sd recognize both usb and sd recognize either usb or sd recognize both usb and sd recognize either usb or sd recognize both usb and sd play/ pause { { { { stop { { { ff { { fb { { folder+ { { folder- { { vol+ { { { { { { vol- { { { { { { +10 { { chng_dev { { { repeat { { { { random { { { { { = enabled = disabled downloaded from: http:///
32/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 21.2 led operation seven types of leds used to display t he lsi operation states are controlled. table 11. shows the types and states of leds. table 11. types of leds and operation description types of leds operation description led_error lights when an error occurs. this happens in the following cases: (1) neither usb memory nor sd memory card is connected. no supported file exists even if these devices are connected. (2) communication error or disconnection occurs in the memory being played. led_play lights during play. blinks during pause. led_psd lights when sd memory card is connected and selected. blinks when sd memory card is connected but sd memory card is not selected. goes off when sd memory card is not connected. led_pusb lights when usb memory is connected and selected. blinks when usb memory is connected but usb memory card is not selected. goes off when usb memory is not connected. led_access lights during access to usb me mory or sd memory card. led_random lights during random play. led_repeat lights during folder repeat. blinks during repeat of one tune. goes off during repeat all tunes in memory downloaded from: http:///
33/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 22. mode2 22.1 command operation you can operate commands via the i 2 c serial interface. when using the lsi in mode2, it can be operated by setting sel_slave to l. the length of command to be s ent varies depending on which command is selected. table 12. shows the command specifications. table 13. shows enabled/disabled state of each command. table 12. command operation description command name comman d byte length command operation description 1st 2nd 3rd 4th- play 2 0x50 0x01 - - when receiving play command during stop, the master starts playing the file currently select ed. the order sorted from the root folder is initially set. when receiving play command during pause, the master restarts playing the file from that point. when a state which disables mp3 decoding for more than 5 seconds during play, status d eco_err is set to h. mp3 decoding is continued. when receiving play command during fast forward (or backward) playing, the master restarts normal playing the file from current point. pause 0x02 - - when receiving pause command during play, the master stops playing the files temporarily. stop 0x03 - - when receiving stop command during play, pause or file search, the master stops playing the file. when receiving stop command during fast forward (or backward) playing, the master stops playing the file. stop command can be received even during busy. vol+ 0x04 - - when sel_vol is set to h, vol+ command is enabled. when receiving vol+ command, the master controls sound volume. sound volume can be controlled at 32 steps from - (minimum volume) to 0db (ma ximum volume). vol- 0x05 - - when sel_vol is set to h, vol-command is enabled. when receiving vol-command, the master controls sound volume. sound volume can be controlled at 32 steps from - (minimum volume) to 0db (ma ximum volume). repeat 0x06 - - this command selects the mode during repeat. repeat command toggles like: repeat all tunes in memory ? repeat one tune ? repeat within folder. when status rpt_off is set as on by "reprand" command, repeat command toggles like: all play in memory ? one file play ? play within folder. in this mode, it stops upon completion of playing. when selecting repeat within fo lder, the master repeats files within the folder being played. the initial setting is repeat all tunes in memory. the last setting to reprand, repeat and random commands will be enabled. this command is as same as the repeat command in mode1. random 0x07 - - this key plays the range of 128 files from the current one being played in the order of sort at random. when status rpt_off is set as on by "reprand" command, repeat command toggles like: one random file play ? all play with random in memo ry. in this mode, it stops upon completion of playing. the last setting to reprand, repeat and random commands will be enabled. this command is as same as the random command in mode1. downloaded from: http:///
34/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 chng_dev 0x08 - - the command selects the device between usb memory and sd memory card. to do this, both devices should be connected or one device should correspond to t he other (usb to sd or sd to usb). otherwise, this key operation is ignored. stop after selecting the device at the top tune of the device. repeat and random settings return to the initial values. abort 0x0c - - this command interrupts tag analysis. it interrupts tag analysis only the file is being played. set_ resume_ info1 8 0x51 0x41 resume info 1byte-6byte this command sets byte 1 to 6 of 42-byte data obtained by read_resume_info. set_ resume_ info2 0x42 resume info 7byte-12byte this command sets byte 7 to 12 of 42-byte data obtained by read_resume_info. set_ resume_ info3 0x43 resume info 13byte-18byte this command sets byte 13 to 18 of 42-byte data obtained by read_resume_info. set_ resume_ info4 0x44 resume info 19byte-24byte this command sets byte 19 to 24 of 42-byte data obtained by read_resume_info. set_ resume_ info5 0x45 resume info 25byte-30byte this command sets byte 25 to 30 of 42-byte data obtained by read_resume_info. set_ resume_ info6 0x46 resume info 31byte-36byte this command sets byte 31 to 36 of 42-byte data obtained by read_resume_info. set_ resume_ info7 0x47 resume info 37byte-42byte this command sets byte 37 to 42 of 42-byte data obtained by read_resume_info. when resume reproduction is possible, play started that music. when resume is impossible, play the head music of media is started. about some kind of setting of resume play, see application note . set_ resume_ info8 0x48 resume info 37byte-42byte this command sets byte 37 to 42 of 42-byte data obtained by read_resume_info. when resume reproduction is possible, it stops in the music. when resume is impossible, it stops at the head of media. about some kind of setting of resume play, see application note. ff 4 0x55 0x01 0x00 0x00 when receiving ff command during play, pause or stop, the master searches the next supported file in the order of sort of the file being played or paused. during play of the last file, the master returns to the first file in the order of sort. operation stops upon completion of search. when tag analysis is set by sel_id3 command, operation stops upon completion of tag analysis. ff&play 0x01 when receiving ff&play command during play, pause or stop, the master search es the next supported file in the order of sort of the file being played or paused. during play of the last file, the master returns to the first file in the order of sort. operation starts playing, after completion of search. when tag analysis is set by sel_id3 command, the master plays the file upon completion of tag analysis. ffp_on 0x02 when receiving ffp_on command during play, pause or stop, the master starts fast forward playing from current point. when music finishes into that ffp_on command is on, the master starts fast forward playi ng from top of the next file. when setting repeat or random, master search next file by setup. ffp_off 0x03 when receiving ffp_off command during fast forward playing, the master restarts normal playing from current point. downloaded from: http:///
35/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 fb 0x02 0x00 0x00 when receiving fb command during play, pause or stop within 1sec from top of file playing, the master searches the previous supported file in the order of sort of files being played or paused. when receiving fb command during play or pause over 1sec from top of file playing, the mast er searches top of present file. the master returns to the last f ile during play of the first file within 1sec from top of file playing. upon completion of search, the operation stops. when tag analysis is set by sel_id3 command, operation stops upon completion of tag analysis. fb&play 0x01 when receiving fb&play command during play, pause or stop within 1sec from top of file pl aying, the master searches the previous supported file in the order of sort of files being played or paused. when receiving fb&play command during play or pause over 1sec from top of file playing, the master searches top of present file. the master returns to the last f ile during play of the first file within 1sec from top of file playing. operation starts playing, after completion of search. when tag analysis is set by sel_id3 command, the master plays the file upon completion of tag analysis. fbp_on 0x02 when receiving fbp_on command during play, pause or stop, the master starts fast backward playing from current point. when music finishes into that fbp_on command is on, the master starts fast backward playing from end of previous file. when setting repeat or random, master search previous file by setup. fbp_off 0x03 when receiving fbp_off command during fast backward playing, the master restarts normal playing from current point. fol+ 0x03 0x00 0x00 when receiving fol+ command during play, pause or stop, the master searches the next folder in the order of sort of the folder in which the file being played or paused exists. the master returns to the first fo lder in the order of sort during play of the last folder. the operation stops upon completion of search. when tag analysis is set by sel_id3 command, operation stops upon completion of tag analysis. fol+&play 0x01 when receiving fol+&play command during play, pause or stop, the master searches the next folder in the order of sort of the folder in which the file being played or paused exists. the master returns to the first fo lder in the order of sort during play of the last folder. operation starts playing, after completion of search. when tag analysis is set by sel_id3 command, the master plays the file upon completion of tag analysis. fol- 0x04 0x00 when receiving fol- command during play, pause or stop, the master search the next folder in t he sort of the folder in which the file being played or paused exists. during play of the first folder, t he master returns to the last folder in the order of sort. the operation stops upon completion of search. when tag analysis is set by sel_id3 command, operation stops upon completion of tag analysis. fol-&play 0x01 when receiving fol-&play command during play, pause or stop, the master searches the next folder in the order of sort of the folder in which the file being played or paused exists. during play of the top folder, the master returns to the first folder in the order of sort. operation starts playing, after completion of search. when tag analysis is set by sel_id3 command, the master plays the file upon completion of tag analysis. downloaded from: http:///
36/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 +10 0x05 0x00 0x00 when receiving +10 command during play, pause or stop, the master searches the s upported file of the 10 th tune in the order of sort of the file being played or paused. when the remaining files to be played are less than 10 in the order of sort, the master returns to the first file. the operation stops upon completion of search. when tag analysis is set by sel_id3 command, operation stops upon completion of tag analysis. +10&play 0x01 when receiving +10&play command during play, pause or stop, the master searches t he supported file of the 10 th tune in the order of sort of the file being played or paused. when the remaining files to be played are less than 10 in the order of sort, the master returns to the first file. operation starts playing, after completion of search. when tag analysis is set by sel_id3 command, the master plays the file upon completion of tag analysis. -10 0x06 0x00 when receiving -10 command during play, pause or stop, the master searches the support ed file of the previous 10 th tune in the order of sort of the file being played or paused. when playing the top 10 or less f iles in the order of sort, the master returns to the first file. the operation stops upon completion of search. when tag analysis is set by sel_id3 command, operation stops upon completion of tag analysis. -10&play 0x01 when receiving -10&play command during play, pause or stop, the master searches the s upported file of the previous 10 th tune in the order of sort of the file being played, paused or stopped. when playing the top 10 or less f iles in the order of sort, the master returns to the first file. operation starts playing, after completion of search. when tag analysis is set by sel_id3 command, the master plays the file upon completion of tag analysis. usb_ mnt_ready 4 0x5d 0x0b 0x01 0x00 *only bu94601kv/bu94603kv this command prepares for usb memory mount. be sure to send this command when status turns to usb_ins=h and busy=l.. set_dout 4 0x51 0x20 0x00 0x58 this command outputs digital audio data as i 2 s (32fs) format. when set_dout command is sent, sel_dout terminal setting is ignored 0x59 this command outputs digital audio data as i 2 s (48fs) format. when set_dout command is sent, sel_dout terminal setting is ignored 0x5b this command outputs digital audio data as i 2 s (64fs) format. when set_dout command is sent, sel_dout terminal setting is ignored 0x01 0x01 this command outputs digital audio data as spdif format. when set_dout command is sent, sel_dout terminal setting is ignored 0xff 0x00 this command stops digital audio output (i 2 s, spdif). when set_dout command is sent, sel_dout terminal setting is ignored set_eq * see chapter 22.3. 2 0x52 0x00 - - this command turns off the eq setting. 0x01 - - pops 0x02 - - jazz 0x03 - - rock 0x04 - - classic 0x05 - - r&b 0x07 - - this command turns off the eq setting. 0x08 - - bass boost1 0x09 - - pops+bass boost1 0x0a - - jazz+bass boost1 0x0b - - rock+bass boost1 downloaded from: http:///
37/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 0x0c - - classic+bass boost1 0x0d - - r&b+bass boost1 0x0f - - bass boost2 set_vol 2 0x53 setting value - - this command sets the sound volume to the 2nd byte value of the command. the setting value ranges 32 steps from 0x00 to 0x1f. any value outside of the above range is ignored. reprand 2 0x54 0x00 - - this command repeats all the tunes within the memory. this is initially set. the last setting to reprand, repeat and random commands will be enabled. 0x01 - - the command repeats playing the file within the folder being played. the last setting to reprand, repeat and random commands will be enabled. 0x02 - - this command repeats playing the file being played. the last setting to reprand, repeat and random commands will be enabled. 0x03 - - this command plays through the range of 128 files in the order of the sort from the current one being played at random. the last setting to reprand, repeat and random commands will be enabled. 0x04 - - this command plays all the tunes within the memory. status rpt_off is set as on. it stops after the last file playing. the last setting to reprand, repeat and random commands will be enabled. 0x05 - - this command plays all the tunes within the folder being played. status rpt_off is set as on. it stops after the last file playing within the folder. the last setting to reprand, repeat and random commands will be enabled. 0x06 - - this command plays one tunes. status rpt_off is set as on. it stops after the file playing. the last setting to reprand, repeat and random commands will be enabled. 0x07 - - this command plays through the range of 128 files in the order of the sort from the current one being played at random. status rpt_off is set as on. it stops after the file playing. the last setting to reprand, repeat and random commands will be enabled. sel_id3 2 0x56 0x00 - - this command does not perform tag analysis. the file played immediately after set will be enabled first. 0x01 - - this command runs tag analysis. the file played immediately after set will be enabled first. upon completion of tag analysis, the data is written to the status register. sel_toc 2 0x57 0x00 - - this command does not perform toc analysis. toc analysis is not performed at initial setting. 0x01 - - when receiving the command, inserting into the device or changing the device, the master analyzes the total folders (including root directory) and total supported files within the device. the number of total supported files conforms to sel_mp3 terminal. when receiving the command, only change from off to on is executed. upon completion of toc analysis, the master returns to the top tune of the device and stops. after toc analysis, the data is written to the status register. downloaded from: http:///
38/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 sel_12mout 2 0x58 0x00 - - this command stops 12mhz clock output from clkout12 terminal. 0x01 - - this command enables 12 mhz clock output from clkout12 terminal. sel_wdt 2 0x5a 0x00 - - this command stops wdt. 0x01 - - this command writes 1 to status wdt_rflg. set_rpm 6 0x5b 0x00 setting this command set up playtime and skiptime for fast forward playing and fast backward playing. fast forward and fast backward playing repeat this cy cle by making {playtime(m) + skiptime(n) +error(o)} into 1 cycle. with an error, it depends on the cajoled error between the minimum decoding unit and playtime, and the real time which searches skiptime. errors differ by every file and every composition in memory. this command set up that playtime is m[15:0]=[4th byte, 3rd byte] and skiptime are n[15:0]=[6t h byte and 5th byte]. initial value set playtime is 300 mili second=m[15:0]=[4 th byte=x01, 3rd byte=x2c] and skiptime is 2100 mili second=n[15:0]=[6 th byte=x08, 5 th byte=x34]. when command set up to 0x0, setting value is initial value. the playtime should set up 300ms or more, and skiptime should set up below (playtime x16). set_ rpm_att 4 0x5b 0x01 setting 0x00 this command set up the attenuation level under fast forward and backward playing. an attenuation level serves as (-6db x [3rd byte]). a setup can be specified from 0x00 to 0x10.as for an initial value, 0x02=-12db is set up. it becomes equivalent to mute by setup of 0x10. set_ upload_ file1 8 0x51 0x51 name[0:5] specify the part of the first half of the file name of the file for file read function. *bury it by 0x20 when the file name(name) doesn't come up to eight bytes. set_ upload_ file2 8 0x51 0x52 name[6:7] ext[0:2] specify the part of the latter half of the file name of the file for file read function. *bury it by 0x20 when the file name(name) doesn't come up to eight bytes. bury it by 0x00 when the file extension doesn't come up to three bytes. it targets neither the file name co mparison since 0x00 of the end in the comparison. upload_ end 2 0x51 0x53 - - the file read function is ended. transmit after completing the file reading. set_tout_m 4 0x5d 0x07 0xyy 0xxx the ack timeout of the command under memory mount is set up. the set point x100 (msec) is timeout. at the time, xx is upper byte and yy is lower byte. an initial value is 30 sec ( yy=0x2c, xx=0x01), and maximum value is 60 sec (yy=0x58, xx=0x02).if set point is over the maximum value, this command is ignored. mount error will be carried out if a timeout occur. set_tout_c 4 0x5d 0x08 0xyy 0xxx the ack timeout of the commands at the time of play or stop o r pause (except during mount) is set up. the set point x100 (msec) is timeout. at the time, xx is upper byte and yy is lower byte. an initial value is 5 sec (yy=0x32, xx=0x00), and maximum value is 60 sec (yy=0x58, xx=0x02). if set point is over the maximum value, this command is ignored. communication error will be carried out if a timeout occur. downloaded from: http:///
39/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 set_ usb_r_ wait 4 0x5d 0x09 0xxx 0x00 the wait time after bus reset is set up at the time of usb memory recognition. the set point (xx) x200 (msec) is wait time. an initial value is 600 msec (xx=0x03), and maximum value is 51.2 sec (xx=0xff). get_ vendor 2 0x5f 0x16 - - a vendor code and product id are stored in comarea. please read comarea after get_vendor command transmission and acquire code data. offset 0x20 vendor code lower byte 0x21 vendor code upper byte 0x22 product code lower byte 0x23 product code upper byte force_ discon_usb 2 0x5d 0x02 - - force mounted usb memory to be disconnected. force_ con_usb 2 0x5d 0x0a - - mounts usb memory again, which mount error occurred. force_ discon_sd 4 0x5d 0x0c 0x01 0x00 force sd memory to be disconnected, which mount error occurred force_ con_sd 4 0x5d 0x0c 0x00 0x00 mounts sd memory again, which was disconnected by force_discon_sd command. set_lun 4 0x5d 0x0d setting 0x00 lun, which usb memory mounts, is specified. lun specified at the time of usb connection mounts. when another lun is already mounted, it re-mounts to specified lun. when not specifying lun, effective lun becomes an auto setup and lun detected first is mounted at the time of usb memory connection. (initial value) reset_lun 2 0x5d 0x0e - - effective lun is set to auto and lun detected first comes to be mounted at the time of usb memory connection. downloaded from: http:///
40/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 table 13. command enabled/disabled in various states after recognizing device, search or pause during play of device search ing during ffp during fbp error recognize either usb or sd recognize either usb or sd recognize either usb or sd recognize both usb and sd recognize either usb or sd recognize both usb and sd play pause stop vol+ vol- repeat random chng_dev abort set_resume_ info1-8 ff ff&play ffp_on ffp_off fb fb&play fbp_on fbp_off fol+ fol+&play fol- fol-&play +10 +10&play -10 -10&play usb_mnt_ready set_dout set_eq set_vol reprand sel id3 sel_toc sel 12mout set_wdt set_rpm set_rpm_att set_upload_file1 after recognizing the usb memory, only the halt condition is the command effective. set_upload_file2 upload_end set_tout_m set_tout_c set_usb_rwait get_vendor force_discon_usb force_con_usb downloaded from: http:///
41/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 force_discon_sd force_con_sd set_lun reset_lun = enabled = disabled downloaded from: http:///
42/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 22.2 status output the operation information, such as internal status, play time information, folder in formation, file information, id3tag information, aactag information and wmatag information, is output using an i 2 c interface. statuses as shown in table 14. mode 2 status register map are output. the status register has a ring buffer structure of offset 0x00-0x7f. t he offset position is automatically incremented after reading byte data. status read specifies offset of the st atus register map. there are two me thods available: to read a desired number of bytes continuously from the offset pos ition and to read the data by one command without specifying the offset pos ition. figure 15. shows the status output commands. table 16. shows the enabled/disabled state of the status output commands. status register outputs a byte data of offset 0x00-0x7f by "little endian" format. (exception exists when using read_id3_title, read_id3_artist, and r ead_id3_album command. see table 15. mode2 status output commands) table 14. mode2 status register map offset status bit7 (msb) bit6 bit5 bit4 bit3 bit2 bit1 bit0 (lsb) 0x00 status1 error 0: no error 1: error occurs search 0: search stop 1: searching sel_id3 0: id3tag off 1: id3tag on sel_toc 0: toc display off 1: toc display on dec_err 0: no error 1: error occurs stop 0: not stopped 1. stopping pause 0: not paused 1: pausing play 0: not played 1: playing 0x01 status2 usbins 0: usb not connected 1: usb connection detected sdins 0: sd not connected 1: sd connection detected usbfile playable file within usb memory 0: absent 1: present sdfile playable file within sd memory 0: absent 1: present mdevusb usb memory 0: not recognized 1: recognized mdevsd sd memory 0: not recognized 1: recognized pdevusb pdevusb usb memory 0: stopping 1: playing/tag analyzing pdevsd pdevusb sd memory 0: stopping 1: playing/tag analyzing 0x02 status3 busy 0: not busy 1: busy mchng tune number change detection 0: tune ended/stopped 1: playing/ stop before playing 0 id3exist tag information 0: not exist 1: exist id3rsid1 id3tag version1 0: absent 1: present id3rsid2 id3tag version2 0: absent 1: present tinfusb total number of folders/files within usb memory 0: not obtained 1: obtained tinfsd total number of folders/files within sd memory 0: not obtained 1: obtained 0x03 status4 0 0 0 0 rpt_off setting after last file playing 0: repeat 1: stop random random play setting 0: off 1: on rep1 one-tune repeat setting 0: off 1: on repfol folder repeat setting 0: off 1: on 0x04 status5 12mout 12 mhz clock output 0: off 1: on wdt_rflg 0: after reset wmaplay play file information * 0: mp3 1: wma , 2: aac 3:device with 2 configurations or more fbp fast backward playing 0: off 1: on ffp fast forward playing 0: off 1: on 0 res_err resume error 0: no error 1: error occurs 0x05 volinf 0 0 0 volinf sound volume information [ 4: 0 ] 0x06 eqinf eqinf equalizer setting information 0000: off 0001: pops 0010: jazz 0011: rock 0100: classic 0101: r&b 1000: bass boost 1001: pops+bass 1010: jazz+bass 1011: rock+bass 1100: classic+bass 1101: r&b+bass 1111 bass boost2 0 0 0 0 0x07 precom precom previous command information 0: normal 1: miss 0x08 dout hub detection flag 0: not detection 1: detection un support device detection flag 0: not detection 1: detection vendor code detection flag 0: apple not detection 1: apple detection 0 0 0 0 dout audio output 0: line output 1: i2s / spdif downloaded from: http:///
43/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 0x09 doutinf doutinf i2s format status 0x58: 32fs(initial value) 0x59: 48fs 0x5b: 64fs 0x00: off 0x01: spdif output 0x0a pfolnl pfolnl playing folder number lower-order byte [7:0] 0x0b pfolnh pfolnh playing folder number upper-order byte [15:8] 0x0c pfilenl pfilenl playing file number lower-order byte [7:0] 0x0d pfilenh pfilenh playing file number upper-order byte [15:8] 0x0e psec playing time second information [7:4]x10 sec. playing time second information [3:0]x1 sec. 0x0f pmin playing time minute information [7:4]x10 min. playing time minute information [3:0]x1 min. 0x10 tfolusbl tfolusbl usb memory total folder number lower -order byte [7:0] 0x11 tfolusbh tfolusbh usb memory total folder number upper-order byte [15:8] 0x12 tfileusbll tfileusbll usb memory total file number lower -order byte [15:0] [7:0] 0x13 tfileusblh tfileusblh usb memory total file number upper-order byte [15:0] [15:8] 0x14 tfileusbhl tfileusbhl usb memory total file number lower -order byte [31:16] [23:16] 0x15 tfileusbhh tfileusbhh usb memory total file number upper-order byte [[31:16] [31:24] 0x16 tfolsdl tfolsdl sd memory total folder number lower -order byte [7:0] 0x17 tfolsdh tfolsdh sd memory total folder number upper-order byte [15:8] 0x18 tfilesdl tfilesdll sd memory total file number lower -order byte [15:0] [7:0] 0x19 tfilesdlh tfilesdlh sd memory total file number upper-order byte [15:0] [15:8] 0x1a tfilesdhl tfilesdhl sd memory total file number lower -order byte [31:16] [23:16] 0x1b tfilesdhh tfilesdhh sd memory total file number upper-order byte [31:16] [31:24] 0x1c langl langl language code information lower -order byte [7:0] 0x1d langh langh language code information upper -order byte [15:8] 0x20 | 0x7f comarea comarea data common area the content varies depending on the status read command. * play file information: the value is 0 when bu94601kv. 3: devi ce with 2 configurations or more is supported only by bu94604b kv. downloaded from: http:///
44/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 table 15. mode2 status output commands command name command status output bytes status 1st byte 2nd byte read_buff 0x5e offset optional the command outputs the desired bytes of data from the offset position specified in the status register map. since the status register functions as a ring buffer of 0x00-0x7f, the master returns to 0x00 after offset position 0x7f during data read. read_status 0x5f 0x00 5 this command outputs the data of offset 0x00-0x04 in the status buffer. read_play_info 0x01 6 this command outputs the data of offset 0x0a-0x0f in the status buffer. read_vol 0x02 1 this command outputs the data of offset 0x05 in the status buffer. read_eq 0x03 1 this command outputs the data of offset 0x06 in the status buffer. read_id3_title 0x04 64 this command outputs the data of tag title. *1 read_id3_artist 0x05 64 this command outputs the data of tag artist.*1 read_id3_album 0x06 64 this command outputs the data of tag album.*1 read_file_name 0x07 64 this command outputs the data of playing file name. see 20.4 read_folder_name 0x08 64 this command outputs the data of folder name includes playing file. see 20.4 read_resume_info * see chapter 22.4. 0x09 42 this command outputs the data to resume. see 22.4 read_version 0x10 1 this command outputs the data of firmware version. read_file_size 0x11 4 the size of a specifi ed file of the file read function is acquired. it outputs with littleendian. when the file doesn't exist, "0xff, 0xff, 0xff, and 0xff" is output. read_file_data 0x12 96 the file data of a specified file of the file read function is read. the 92byte data reading is possible by one time. four head bytes are file offsets. it outputs it with littleendian. read_lun 0 17 1 in case of auto detection mode of lun,lun of mounted usb memory can be read. if lun is specified using the "set_lun" command, specified lun of mounted usb memory can be read. but if failed to mount, 0xff is read. attention) when memory connected to multi-card reader is removed or re-inserted, lun read by this command is not correct until mount of re-inserted media is completed. read_lun_num 0 18 1 read the total of lun of the usb memory which is connected now. downloaded from: http:///
45/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 read_set_lun 0 19 1 read lun specified by the "set_lun" command. in not setting up, 0xff is read. *1 bom(byte order mark) might enter two head bytes according to id3 data. status register outputs byte data by "big endian" format when wma tag reading. table 16. command enabled/disabled in various states after recognizing device (stopping after searching) during play of device searching error read_buff read_status read_play_info read_vol read_eq read_id3_title read_id3_album read_id3_artist read_file_name read_folder_name read_resume_info read_version read_file_size after recognizing the usb memory, only the halt condition is the command effective. read_file_data read_lun read_lun_num read_set_lun { = enabled, = disabled downloaded from: http:///
46/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 22.3 equalizer you can select 5 types of equalizer and 2 types of bassboost for the audio line output using a command (see table 7). combination of equalizer and bassboost1 is available. clipping may occur by the combination of volume and equalizer setting. equalizer setting is enabled even when line output is not selected. no change of sound quality by the equalizer is found in digital outputs. figures 28 to 33 show the frequency characteristics of each filter. figure 28 pops frequency characteristics figure 29 jazz frequency characteristics pops -10 -5 0 5 10 15 20 10 100 1000 10000 100000 freq.(hz) mag.(db) pops(0x52, 0x01) pops+bassboost1(0x52, 0x09) jazz -10 -5 0 5 10 15 20 10 100 1000 10000 100000 freq.(hz) mag.(db) jazz(0x52, 0x02) jazz+bassboost1(0x52, 0x0a) downloaded from: http:///
47/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 figure 30 rock frequency characteristics figure 31 classic frequency characteristics rock -10 -5 0 5 10 15 20 10 100 1000 10000 100000 freq.(hz) mag.(db) rock(0x52, 0x03) rock+bassboost1(0x52, 0x0b) classic -10 -5 0 5 10 15 20 10 100 1000 10000 100000 freq.(hz) mag.(db) classic(0x52, 0x04) classic+bassboost1(0x52, 0x0c) downloaded from: http:///
48/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 figure 32 r&b figure 33 bass boost r&b -10 -5 0 5 10 15 20 10 100 1000 10000 100000 freq.(hz) mag.(db) r&b(0x52, 0x05) r&b+bassboost1(0x52, 0x0d) bassboost -10 -5 0 5 10 15 20 10 100 1000 10000 100000 freq.(hz) mag.(db) bassboost1(0x52, 0x08) bassboost2(0x52, 0x0f) downloaded from: http:///
49/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 22.4 resume information this lsi outputs the information required to implement the resume function using the read_resume_info command. table 17. shows the resume informati on status register structure. table 17. resume information register structure status offset resume information 0x20-0x49 resume information data [42 bytes] i. resume information data : shows the files information and plays information now. this is a number uniquely set to the lsi. since the above 42-byte resume information is used to execute resume play, do not change the contents before use. when you use changed content s, the action cannot assure. you can implement the resume function by r eading the resume information read using the read_resume_info command and then writing the information using the set_resume_info1-7 command. after set_resume_info1-7 is all written, the lsi automatically searches and plays a resume file from the time, which read read_resume _info command upon completion of writing of set_resume_info7. 22.5 language code information this lsi outputs language code information to status register. (offset=0x1c and 0x1d) table 18. shows the language code info rmation status register structure. table 18. language code information register structure langh offset=0x1d langl offset=0x1c language code 0x00 0x00 id3v1 tag or iso8859-1 (id3v2 tag) 0x00 0x01 utf-16 (id3v2 tag) 0x00 0x02 utf-16be (id3v2 tag) 0x00 0x03 utf-8 (id3v2 tag or aac tag itunes meta-data) * 0x00 0x49 utf-16le (wma tag) * *bu94601kv doesnt support wma/aac tag. downloaded from: http:///
50/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 23. mode3 mode3 specifies and plays the file to be played by the mast er microcomputer by outputting the file/folder status information, written to usb me mory or sd memory card, to the master microcomputer. 23.1 command operation the lsi sends commands to obtain the file/folder informa tion in usb memory or sd memory card, to analyze id3tag, to analyze wmatag, to analyze aactag, and to set a file to be played and start playing it. table 19. shows the commands available in mode3. when sending a command other than listed below in mode3, it is ignored. table 19. mode3 command command name command byte length command operation description 1st 2nd 3rd- pause 2 0x50 0x02 - when receiving pause command during play, the master stops playing file temporarily. stop 0x03 - this command stops the oper ations of tag analysis. this command stops playing file and stop at top of this file. vol+ 0x04 - when sel_vol is set to h, vol+ command is enabled. when receiving vol+ command, the master controls sound volume. sound volume can be controlled at 32 steps from - (minimum volume) to 0db (maximum volume). vol- 0x05 - when sel_vol is set to h, vol-command is enabled. when receiving vol-command, the master controls sound volume. sound volume can be controlled at 32 steps from - (minimum volume) to 0db (maximum volume). chng_dev 0x08 - the command selects the device between usb memory and sd memory card. to do this, both devices should be connected or one device should correspond to the other (usb to sd or sd to usb). otherwise, this command is ignored. after selecting the device, the lsi waits for a command. get_direct 0x09 - this command obtains the folder information (*see 23.3) and file information (*see 23.3) for the folder set by set_direct. read the information using the status commands read_folder_info and read_file_info. the status of ana_end, folinf, filinf, folfull and filfull are reset. get_number 0x0a - this command obtains the number of files and folders for the folder set by set_direct. read the information using status command read_number. the number of unsupported files is ignored. the statuses of ana_end are reset. get_id3 0x0b - this command performs tag analysis for the valid file set by set_direct. the command also analyzes even if the folder is not specified. however, at the end of analysis, a status in which tag information is not contained will be output. - the statuses of id3exist , id3rsid1 and id3rsid2 are reset. downloaded from: http:///
51/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 abort 0x0c - this command stops the operati ons of tag analysis, folder analysis and file analysis. the statuses of ana_end, folinf, filinf, folfull, filfull, "id3exist", "id3rsid1" and "id3rsid2" are reset. play_direct 0x0d - this command starts playing the aac/wma/mp3 file set by set_direct. the command plays the file even when the preset file is not an supported file or when the folder is specified, the command plays the specified one. if mp3 decode disabled is detected for 5 seconds or longer, the command outputs status "deco_err"=h. usb_ mnt_ready 4 0x5d 0x0b 0x01 0x00 *only bu94601kv/bu94603kv this command prepares for usb device mount. be sure to send this command when status turns to usb_ins=h and busy=l.. set_dout 4 0x51 0x20 0x00 0x58 this command outputs digital audio data as i 2 s (32fs) format. when set_dout command is sent, sel_dout terminal setting is ignored 0x59 this command outputs digital audio data as i 2 s (48fs) format. when set_dout command is sent, sel_dout terminal setting is ignored 0x5b this command outputs digital audio data as i 2 s (64fs) format. when set_dout command is sent, sel_dout terminal setting is ignored 0x01 0x01 this command outputs digital audio data as spdif format. when set_dout command is sent, sel_dout terminal setting is ignored 0xff 0x00 this command stops digital audio output (i 2 s, spdif). when set_dout command is sent, sel_dout terminal setting is ignored set_number 6 0x21 0xxx this command sets the number of obtained folders for those set by set_direct. parameter: number of obtained folders: 2 bytes + number of obtained files: 2 bytes. by specifying 0, all the folders and files are obtained. set_ resume_ info1 8 0x51 0x41 resume info 1byte-6byte this command sets byte 1 to 6 of 42-byte data obtained by read_resume_info. set_ resume_ info2 0x42 resume info 7byte-12byte this command sets byte 7 to 12 of 42-byte data obtained by read_resume_info. set_ resume_ info3 0x43 resume info 13byte-18byte this command sets byte 13 to 18 of 42-byte data obtained by read_resume_info. set_ resume_ info4 0x44 resume info 19byte-24byte this command sets byte 19 to 24 of 42-byte data obtained by read_resume_info. set_ resume_ info5 0x45 resume info 25byte-30byte this command sets byte 25 to 30 of 42-byte data obtained by read_resume_info. set_ resume_ info6 0x46 resume info 31byte-36byte this command sets byte 31 to 36 of 42-byte data obtained by read_resume_info. downloaded from: http:///
52/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 set_ resume_ info7 0x47 resume info 37byte-42byte this command sets byte 37 to 42 of 42-byte data obtained by read_resume_info. when resume reproduction is possible, play started that music. when resume is impossible, play the head mu sic of media is started. about some kind of setting of resume play, see application note. set_ resume_ info8 0x48 resume info 37byte-42byte this command sets byte 37 to 42 of 42-byte data obtained by read_resume_info. when resume reproduction is possible, it stops in the music. when resume is impossible, it stops at the head of media. about some kind of setting of resume play, see application note. set_eq *see chapter 22.3. 2 0x52 0x00 - this command turns off eq setting. 0x01 - pops 0x02 - jazz 0x03 - rock 0x04 - classic 0x05 - r&b 0x07 - this command turns off eq setting. 0x08 - bass boost 0x09 - pops+bass 0x0a - jazz+bass 0x0b - rock+bass 0x0c - classic+bass 0x0d - r&b+bass 0x0f - bass boost2 set_vol 0x53 setting value - set sound volume the second byte value of the command. the setting values are 32 steps ranging from 0x00 to 0x1f. a value specified outside the above range will be ignored. ffp_on 4 0x55 0x01 0x02 0x00 . start the fast-forwarding playback from a present playback position by this command of playbacking and pausing. ffp_off 0x03 0x00 . stop the fast-forwarding playback by this command fast-forwarding playback, and usually playback. fbp_on 0x02 0x02 0x00 . start the rewinding playback from a present playback position by this command of playbacking and pausing. fbp_off 0x03 0x00 . stop the rewinding playback by this command rewinding playback, and usually playback. sel_12mout 2 0x58 0x00 - this command stops 12 mhz clock output from clkout12 terminal. 0x01 - this command enables 12 mhz clock output from clkout12 terminal. set_direct 8 0x59 0x00 0xxx this command specifies t he current position of the folder/file by specifying the folder/file information access data (6 bytes). specify access data (6 bytes) at 0xxx. by specifying 0, the position is set to the root folder. set_wdt 2 0x5a 0x00 - this command stops watch dog timer. 0x01 - this command writes 1 to status wdt_rflg. downloaded from: http:///
53/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 set_rpm 6 0x5b 0x00 setting this command set up playtime and skiptime for fast forward playing and fast backward playing. fast forward and fast backward playing repeat this cycle by making {playtime(m) + skiptime(n) +error(o)} into 1 cycle. with an error, it depends on the cajoled error between the minimum decoding unit and playtime, and the real time which searches skiptime. errors differ by every file and every composition in memory. this command set up that playtime is m[15:0]=[4th byte, 3rd byte] and skiptime are n[15:0]=[6th byte and 5th byte]. initial value set playtime is 300 mili second=m[15:0]=[4 th byte=x01, 3rd byte=x2c] and skiptime is 2100 mili second=n[15:0]=[6 th by te=x08, 5 th byte=x34]. when command set up to 0x0, setting value is initial value. the playtime should set up 300ms or more, and skiptime should set up below (playtime x16). set_rpm_att 4 0x5b 0x01 setting 0x00 this command set up the attenuation level under fast forward and backward playing. an attenuation level serves as (-6db x [3rd byte]). a setup can be specified from 0x00 to 0x10.as for an initial value, 0x02=-12db is set up. it becomes equivalent to mute by setup of 0x10. set_ upload_file1 8 0x51 0x51 name[0:5] specify the part of the first half of the file name of the file for file read function. *bury it by 0x20 when the file name(name) doesn't come up to eight bytes. set_ upload_file2 8 0x51 0x52 name[6:7] ext[0:2] specify the part of the latter half of the file name of the file for file read function. *bury it by 0x20 when the file name(name) doesn't come up to eight bytes. bury it by 0x00 when the file extension doesn't come up to three bytes. it targets neither the file name comparison since 0x00 of the end in the comparison. upload_end 2 0x51 0x53 - - the file read function is ended. transmit after completing the file reading. set_tout_m 4 0x5d 0x07 0xyy 0xxx the ack timeout of the command under memory mount is set up. the set point x100 (msec) is timeout. at the time, xx is upper byte and yy is lower byte. an initial value is 30 sec (yy=0x2c, xx=0x01), and maximum value is 60 sec (yy=0x58, xx=0x02).if set point is over the maximum value, this command is ignored. mount error will be carried out if a timeout occur. set_tout_c 4 0x5d 0x08 0xyy 0xxx the ack timeout of the commands at the time of play or stop or pause (except during mount) is set up. the set point x100 (msec) is timeout. at the time, xx is upper byte and yy is lower byte. an initial value is 5 sec (yy=0x32, xx=0x00), and maximum value is 60 sec (yy=0x58, xx=0x02). if set point is over the maximum value, this command is ignored. communication error will be carried out if a timeout occur. set_usb_ r_wait 4 0x5d 0x09 0xxx 0x00 the wait time after bus reset is set up at the time of usb memory recognition. the set point (xx) x200 (msec) is wait time. an initial value is 600 msec (xx=0x03), and maximum value is 51.2 sec (xx=0xff). downloaded from: http:///
54/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 get_ vendor 2 0x5f 0x16 - - a vendor code and product id are stored in comarea. please read comarea after get_vendor command transmission and acquire code data. offset 0x20 vendor code lower byte 0x21 vendor code upper byte 0x22 product code lower byte 0x23 product code upper byte force_ discon_usb 2 0x5d 0x02 - - force mounted usb memory to be disconnected. force_ con_usb 2 0x5d 0x0a - - mounts usb memory again, which mount error occurred. force_ discon_sd 4 0x5d 0x0c 0x01 0x00 force sd memory to be disconnected, which mount error occurred force_ con_sd 4 0x5d 0x0c 0x00 0x00 mounts sd memory again, which was disconnected by force_discon_sd command. set_lun 4 0x5d 0x0d setting 0x00 lun, which usb memory mounts, is specified. lun specified at the time of usb connection mounts. when another lun is already mounted, it re-mounts to specified lun. when not specifying lun, effective lun becomes an auto setup and lun detected first is mounted at the time of usb memory connection. (initial value) reset_lun 2 0x5d 0x0e - - effective lun is set to auto and lun detected first comes to be mounted at the time of usb memory connection. downloaded from: http:///
55/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 table 20. command enabled/disabled in various statuses after recognizing device * analyzing during play of device searching error recognize either usb or sd recognize both usb and sd recognize either usb or sd recognize both usb and sd recognize either usb or sd recognize both usb and sd pause stop vol+ vol- chng_dev get_direct get_number get_id3 abort play_direct usb_mnt_ready set_dout set_number set_resume_ info1-7 set_eq set_vol ffp_on ffp_off fbp_on fbp_off sel 12mout set_direct set_wdt set_rpm set_rpm_att set_upload_file1 after recognizing the usb memory, only the halt condition is the command effective. set_upload_file2 upload_end set_tout_m set_tout_c set_usb_rwait get_vendor force_ discon_usb force_con_usb force_discon_sd force_con_sd set_lun reset_lun { = enabled = disabled * analyzing shows the file/folder information is being obtained after get_direct command is transmitted. downloaded from: http:///
56/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 23.2 status output the lsi outputs the operation information, such as internal status, play time information, folder information, file information id3tag info rmation, aactag information, and wmatag information, using the i 2 c interface. the statuses as shown in table 21. mode3 status regist er map are output. there are two methods available: to read a desired number of bytes continuously from the offset position and to read the data by one command without specifying the offset position. figure 23. shows t he status output commands. table 23 shows the enabled/disabled state of the status commands. the status register has a ring buffer structure of offset 0x00-0x7f. t he offset position is automatically incremented after reading byte data. status register outputs a byte data of offset 0x00-0x7f by "little endian" format. (exception exists when using read_id3_title, read_id3_artist, and read_i d3_album command. see t able 22. mode3 status output commands) table 21. mode3 status output offset status bit7 (msb) bit6 bit5 bit4 bit3 bit2 bit1 bit0 (lsb) 0x00 status1 error 0: no error 1: error occurs search 0: search stop 1: searching 0 0 dec_err 0: no error 1: error occurs stop 0: not stopped 1. stopping pause 0: not paused 1: pausing play 0: not played 1: playing 0x01 status2 usbins 0: usb not connected 1: usb connection detected sdins 0: sd not connected 1: sd connection detected usbfile playable file within usb memory 0: absent 1: present sdfile playable file within sd memory 0: absent 1: present mdevusb usb memory 0: not recognized 1: recognized mdevsd sd memory 0: not recognized 1: recognized pdevusb pdevusb usb memory 0: stopping 1: playing/id3tag analyzing pdevsd pdevusb sd memory 0: stopping 1: playing/id3tag analyzing 0x02 status3 busy command busy 0: not busy 1: busy mchng tune number change detection 0: tune ended/stopped 1: playing 0 id3exist tag information 0: not exist 1. exist id3rsid1 id3tag version1 0: absent 1: present id3rsid2 id3tag version2 0: absent 1: present 0 0 0x03 status4 anaend 0: analyzing 1: analysis completed folinf folder information 0: absent 1: present folfull folder buffer 0: not full 1: full fileinf folder information 0: absent 1: present filefull folder buffer 0: not full 1: full 0 0 0 0x04 status5 12mout 12 mhz clock output 0: off 1: on wdt_rflg 0:after reset wmaplay play file information 0: mp3 1: wma , 2: aac 3:device with 2 configurations or more fbp fast backward playing 0: off 1: on ffp fast forward playing 0: off 1: on 0 res_err resume error 0: no error 1: error occurs 0x05 volinf 0 0 0 volinf sound volume information [ 4: 0 ] 0x06 eqinf eqinf equalizer setting information 0000: off 0001: pops 0010: jazz 0011: rock 0100: classic 0101: r&b 1000: bass boost 1001: pops+bass 1010: jazz+bass 1011: rock+bass 1100: classic+bass 1101: r&b+bass 1111 bass boost2 0 0 0 0 0x07 precom precom previous command information 0: normal 1: miss 0x08 dout hub detection flag 0: not detection 1: detection un support device detection flag 0: not detection 1: detection vendor code detection flag 0: apple not detection 1: apple detection 0 0 0 0 dout audio output 0: line output 1: i2s / spdif downloaded from: http:///
57/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 0x09 doutinf doutinf i2s format status 0x58: 32fs(initial value) 0x59: 48fs 0x5b: 64fs 0x0a pfolnl 00h 0x0b pfolnh 00h 0x0c pfilenl 00h 0x0d pfilenh 00h 0x0e psec playing time second information [7:4]x10 second. playing time second information [3:0]x1second. 0x0f pmin playing time minute information [7:4]x10 min. playing time minute information [3:0]x1 min. 0x10 tfoll tfoll current folder total folder number lower-order byte [7:0] 0x11 tfolh tfolh current folder total folder number upper-order byte [15:8] 0x12 tfilel tfilel current folder total file number lower-order byte [15:0] [7:0] 0x13 tfileh tfileh current folder total file number upper-order byte [15:0] [15:8] 0x14 resfoll resfoll remaining analysis folder number lower-order byte [7:0] 0x15 resfolh resfolh remaining analysis folder number upper-order byte [15:8] 0x16 resfilel resfilel remaining analysis file number lower-order byte [7:0] 0x17 resfileh resfileh remaining analysis file number upper-order byte [15:8] 0x18 setfoll setfoll folder acquisition setting value lower-order byte [7:0] 0x19 setfolh setfolh folder acquisition setting value upper-order byte [15:8] 0x1a setfilel setfilel file acquisition setting value lower-order byte [7:0] 0x1b setfileh setfileh file acquisition setting value upper-order byte [15:8] 0x1c langl langl language code information lower -order byte [7:0] 0x1d langh langh language code information upper -order byte [15:8] 0x20 | 0x7f comarea comarea data common area the content varies depending on the status read command. * play file information: the value is 0 when bu94601kv. 3: devi ce with 2 configurations or more is supported only by bu94604b kv. downloaded from: http:///
58/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 table 22. mode3 status output commands command name command status output bytes status 1st byte 2nd byte read_buff 0x5e offset optional this command outputs the specified offset byte data from status buffer. read_status 0x5f 0x00 5 this command outputs offset 0x00-0x04 of status buffer. read_play_info 0x01 6 this command outputs offset 0x0a-0x0f of status buffer. read_vol 0x02 1 this command outputs offset 0x05 of status buffer. read_eq 0x03 1 this command outputs offset 0x06 of status buffer. read_id3_title 0x04 64 this command outputs the data of tag title. *1 read_id3_artist 0x05 64 this command outputs the data of tag artist. *1 read_id3_album 0x06 64 this command outputs the data of tag album. *1 read_file_name 0x07 64 this command outputs the data of playing file name. see 20.4 read_folder_name 0x08 64 this command outputs the data of folder name includes playing aac/wma/mp3 file. see 20.4 read_resume_info 0x09 42 . acquire resume information in this command while being playbacking or pausing. . set the data acquired in this command as it is when setting resume information by "set_resume_info1-7". read_number 0x0a 4 this command outputs offset 0x10-0x13 of status buffer. read_rest_num 0x0b 4 this command outputs offset 0x14-0x17 of status buffer. read_set_num 0x0c 4 this command outputs offset 0x18-0x1b of status buffer. read_folder_info 0x0d 76 this command outputs the result of folder analysis by "get_direct" command. see 23.3. read_file_info 0x0e 76 this command outpu t s the result of file analysis by "get_direct" command. see 23.3. read_clas 0x0f 4 this command outputs the data of file cluster number. use to check file when "play_direct". read_version 0x10 1 this command outputs the data of firmware version. read_file_size 0x11 4 the size of a specifi ed file of the file read function is acquired. it outputs with ittleendian. when the file doesn't exist, "0xff, 0xff, 0xff, and 0xff" is output. read_file_data 0x12 96 the file data of a specified file of the file read function is read. the 92byte data reading is possible by one time. four head bytes are file offsets. it outputs with littleendian. downloaded from: http:///
59/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 read_lun 0x17 1 in case of auto detection mode of lun, lun of mounted usb memory can beread. if lun is specified using the "set_lun" command, specified lun of mounted usb memory can be read. but if failed to mount, 0xff is read. attention) when memory connected to multi-card reader is removed or re-inserted, lun read by this command is not correct until mount of re-inserted media is completed. read_lun_num 0x18 1 read the total of lun of the usb memory which is connected now. read_set_lun 0x19 1 read lun specified by the "set_lun" command. in not setting up, 0xff is read. *1 bom(byte order mark) might enter two head bytes according to id3 data. status register outputs byte data by "big endian" format when wma tag reading. downloaded from: http:///
60/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 table 23. after recognizing device *1 analyzing during play of device searching error read_buff read_status read_play_info *2 read_vol read_eq read_id3_title read_id3_ artist read_id3_album read_file_name read_folder_name read_resume_info read_number read_rest_num read_set_num read_folder_info read_file_info read_clas read_version read_file_size after recognizing the usb memory, only the halt condition is the command effective. read_file_data read_lun read_lun_num read_set_lun { = enabled = disabled *1 analyzing shows the file/folder in formation is being obtained after ge t_direct command is transmitted. *2read_play_info command when an error occurs can be received. however, status output may not send correct data. downloaded from: http:///
61/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 23.3 folder informa tion/file information for analysis performed by get_direct command, re ad 76 bytes from the status register comarea (0x20-0x6b) using status commands read_folder_i nfo and read_file_info. each of the status register structures when read_folder_info and read_file_info are sent is shown below. (1) folder information when the folder is specified using set_direct, the ls i allows you to fetch the folder information in the specified folder from the memory device at get_direct and read folder information using read_folder_info. table 24. shows the status register structure. table 24. folder information register structure status offset folder information 0x20-0x25 access data [6 bytes] 0x26-0x27 reserve [2 bytes] 0x28-0x2b cluster number [4 bytes] 0x2c-0x6b folder name [64 bytes] i. access data : shows the position where the folder information is written in the memory. ii. reserve : all 0s are output. iii. cluster number : shows the cluster number where the folder information is written in the memory. iv. folder name : outputs the folder name from the leftmost position. (2) file information when the folder is specified using set_direct, the lsi allows you to fetch the file information in the specified folder from the memory device at get_direct and read file information using read_file_info. table 25. shows the status register structure. table 25. file information register structure status offset file information 0x20-0x25 access data [6 bytes] 0x26 judge file type[1 bytes] * 0x27 reserve [1bytes] 0x28-0x2b cluster number [4 bytes] 0x2c-0x6b file name [64 bytes] i. access data : shows the position where the file information is written in the memory. ii. judge file type : output 0 when play mp3 fi le, output 1 when play wma file, output 2 when play aac file. iii. reserve : all 0s are output. iv. cluster number : shows the cluster number wher e the file information is written in the memory. v. file name : outputs the file name from the leftmost position. * reserve [1bytes] when bu94601kv. 23.4 language code information this lsi outputs language code information to status register. (offset=0x1c and 0x1d) see chapter 22.5. downloaded from: http:///
62/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 24. watchdog timer this system builds watchdog timer(wdt) function. after reset, wdt function is enabled on mode1, mode 2 and mode3. wdt is enabled always on mode1. on mode2 and mode3, wdt function can disable by co mmand set_wdt(0x5a,0x00). after wdt function is disabled, this function cannot enable until a reset from external pin. when wdt function is enabled and system is hang-up, watchdog timer function generates reset. when you want to watch reset of wdt from master mi cro controller, write command set_wdt(0x5a,0x01). after write command set_wdt(0x5a,0x01), status wdt_rflg is 1. wdt_rflg is bit6 of status5(offset;x 04). this status is 0 after reset. therefore, when this status returned to 0 from 1, this system generated a reset. 25. irpto (only bu94604bkv) the device can be controlled about mo de2 and 3 about the device where tw o configuration or more is detected at usb device connection enum eration by the following commands. 25.1 command operation as for the command specificati on that can be used, it is table vii. it shows in 6.1. table 26. command operation explanation command name command bmre quest type breq uest wvalue windex wlength 1st 2nd 3rd 4th 5th 6th 7th 8th explanation get_ descriptor 0x5c 0x00 0x00 0x00 *1 0x80 0x06 0x0100 0x0000 0x0008 acquire the size of the device descriptor. 0x01 set value 0x80 0x06 0x0100 0x0000 set value acquire the descriptor of the number of bytes for a set value. get_config 0x01 0x00 set value 0x80 0x06 0x02_ set value 0x0000 0x0008 acquire the size of the configuration descriptor of the index of a set value. 0x01 set value 1 set value 2 0x80 0x06 0x02_ set value 1 0x0000 set value 2 acquire the configuration descriptor of the block of set value 2(one block 96 bytes) of the index of set value 1. set_config 0x01 0x02 set value 0x00 0x09 set value 0x0000 0x0000 set it to the configuration of a set value. *2 get_string 0x02 0x00 0x00 0x00 0x00 0x80 0x06 0x0300 0x0000 0x0040 acquire language id. set value 1 set value 2 set value 3 0x80 0x06 0x03_ set value 1 set value 2_3 0x0040 acquire the size of the string of the index of setting 1 of languages id of set values 2 and 3. 0x01 set value 1 set value 2 set value 3 set value 4 0x80 0x06 0x03_ set value 1 set value 3_4 set value 2 acquire the string of the size of index and set value 2 of set value 1 of languages id of set values 3 and 4. downloaded from: http:///
63/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 set_device 0x5c 0x03 ep/io type wmaxpkt lo byte wmaxpkt hi byte binterval end point descriptor setting ep/io d7 in 0 out) d3-d0 endpoint) type 0x00(control transfer 0x01 isochronous transfer 0x02 bulk transfer 0x03 interrupt transfer) wmaxpkt supported size of the maximum packet binterval polling interval *begin polling on interrupt in forwarding after it sets it. get_hid_ report 0x04 wvalue lo byte wvalue hi byte windex lo byte windex hi byte wlength lo byte wlength hi byte 0x81 0x06 wvlaue windex wlength acquire the hid report descriptor. *2 set_hid_ report 0x05 wvalue lo byte wvalue hi byte windex lo byte windex hi byte wlength lo byte wlength hi byte 0x21 0x09 wvlaue windex wlength set_report request command setting for hid class device. 0x06 0xn (n=0x01 to 0x0d) data (n-1)*5 data (n-1)*5+1 data (n-1)*5+2 data (n-1)*5+3 data (n-1)*5+4 data setting at set_report request command for hid class device. 0x06 0x0e 0x00 0x00 0x00 0x00 0x00 transmission of set_report request command for hid class device. the set_hid_report command is completed by transmitting this command. *2 get_int 0x07 0x00 0x00 acquire the interrupt forwarding receive data. 0x01 0x00 acquire the reception byte of hid report. the reception byte acquires the size of the report acquired in hid_report_descriptor. an effective actual data size becomes below this size. set_masst 0x08 0x00 0x00 transmit this command when you connect the connected device as a mass storage class device. set_iso_ start 0x09 0x00 0x00 begin the isochronous in forwarding data reproduction. set_iso_ stop 0x01 0x00 stop the isochronous in forwarding data reproduction. set_fs 0x0a set value 0x00 change the sample rate. 0x00 32khz 0x01 44.1khz 0x02 48khz get_report 0x0b set value 0x00 acquire the report data of the block of a set value. set_ interface 0x0c wvalue lo byte wvalue hi byte windex lo byte windex hi byte 0x01 0x0b wvalue windex 0x0000 switch wvalue to the interface of windex. set_ vendor 0xfe 0x00 set value 1 set value 2 wvalue lo byte wvalue hi byte set value 2 set value 1 wvlaue windex wlength 0x01 windex lo byte windex hi byte wlength lo byte wlength hi byte usb device request. 0xff 0xn (n=0x01 to 0x0d) data (n-1)*5 data (n-1)*5+1 data (n-1)*5+2 data (n-1)*5+3 data (n-1)*5+4 data setting for usb device request. 0x0e 0x00 0x00 0x00 0x00 0x00 data transmission for usb device request. *2 *1 the transmission of " " is unnecessary. *2 after confirming busy status l output, wait of 3ms is necessary when the command transmission is done. downloaded from: http:///
64/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 notes for use (1)power on reset please keep the terminal resetx at t he low level when the power supply star ts. please make the terminal resetx high level after 5us after 3.3v system power supply and the o scillation of the system clock is steady. moreover, please make the terminal resetx low level during 5us or more when resetting it while operating. (2) about compatibility in usb memory device and sd memory card according to the file structure and communication speed of an usb memory, sd memory card, this lsi might not play back correctly. (3) about turning on the power supply current rush might flow momentarily by the order of turnin g on the power supply and the delay in ic with two or more power supplies, and note the capacity of the power supply coupling, the power supply, and width and drawing the gnd pattern wiring. (4) about absolute maximum rating when the absolute maximum rating such as the applied voltage and the ranges of the operating temperature is exceeded, lsi might be destroyed. please apply nei ther voltage nor the temperature that exceeds the absolute maximum rating. please execute physical measures for safety such as fuse when it is thought to exceed the absolute maximum rating, and examine it so that the condition to exceed the absolute maximum rating is not applied to lsi. (5) about gnd voltage in any state of operation must be the lowest voltage about the voltage of t he terminal gnd. please actually confirm the voltage of each terminal is not a voltage that is lower than the terminal gnd including excessive phenomenon. (6) about design of overheatin g malfunction preventive circuit please design overheating malfunction preventive circuit with an enough margin in consideration of a permissible loss in the state of using actually. (7) about the short between terminals and the mounting by mistake please note the direction and the gap of position of lsi enough about lsi when you mount on the substrate. lsi might be destroyed when mounting by mistake and energizing. moreover, lsi might be destroyed when short-circuited by entering of the foreign substances between the termi nal and gnd, between terminals, between the terminal and the power supply of lsi. (8) about operation in strong electromagnetic field use in strong electromagnetic field has the possibility of malfunctioning and evaluate it enough, please. (9) playing time of mp3 file the playing time when it can be acquired at the time of pl aying the mp3 file, may shift when fast forward playing, rewinding playing, and vbr playing. (10) about wma windows media audio is the music compression technology which microsoft corp. developed. windows media is the registered trademark of u.s. micr osoft corporation in the u.s., and other countries. (11) about i 2 c format i/f although this lsi has adopted the i 2 c format, the level shifter circuit is not built in. for this reason, level shifter is needed for connection with the device besides the range of operating power supply voltage of this lsi. (12) about " made for ipod / iphone / ipad license " for using of bu94604bkv, it is necessary to become a licensee of apple inc. regarding "made for ipod/iphone/ipad license" status of this document the japanese version of this document is the formal specification. a customer may use this translation version only for a reference to help reading the formal version. if there are any differences in translation version of this document, formal version takes priority. downloaded from: http:///
65/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 information about ordering part number b u 9 4 6 0 x x k v - x x x x part number bu94601kv (mp3 support) bu94603kv (aac/wma/mp3 support) bu94604bkv (aac/wma/mp3 + ipod support) package kv: vqfp64 packaging and forming specification zae2: reel-formed emboss taping none: tray, tube external dimension bu94601kv/bu94603kv/bu 94604bkv (vqfp64) b b b mark name image part number part number marking ordering part number bu94601kv bu94601kv bu94601kv-zae2 bu94603kv bu94603kv bu94603kv-zae2 bu94604bkv bu94604bkv bu94604bkv-zae2 vqfp64 (top view) part number marking lot numbe r 1pin mark downloaded from: http:///
66/66 datasheet datasheet bu94601kv bu94603kv bu94604bkv tsz02201-0v2v0e600010-1-2 ? 2012 rohm co., ltd. all rights reserved. 2012.07.12 rev.001 www.rohm.com tsz22111 ? 15 ? 001 revision history date revision changes 12.jul.2012 001 new release downloaded from: http:///
datasheet d a t a s h e e t notice - ge rev.002 ? 2014 rohm co., ltd. all rights reserved. notice precaution on using rohm products 1. our products are designed and manufac tured for application in ordinary elec tronic equipments (such as av equipment, oa equipment, telecommunication equipment, home electroni c appliances, amusement equipment, etc.). if you intend to use our products in devices requiring ex tremely high reliability (such as medical equipment (note 1) , transport equipment, traffic equipment, aircraft/spacecra ft, nuclear power controllers, fuel c ontrollers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (specific applications), please consult with the rohm sale s representative in advance. unless otherwise agreed in writing by rohm in advance, rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ro hms products for specific applications. (note1) medical equipment classification of the specific applications japan usa eu china class class class b class class class 2. rohm designs and manufactures its products subject to strict quality control system. however, semiconductor products can fail or malfunction at a certain rate. please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe desi gn against the physical injury, damage to any property, which a failure or malfunction of our products may cause. the following are examples of safety measures: [a] installation of protection circuits or other protective devices to improve system safety [b] installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. our products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditio ns, as exemplified below. accordin gly, rohm shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of an y rohms products under any special or extraordinary environments or conditions. if you intend to use our products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] use of our products in any types of liquid, incl uding water, oils, chemicals, and organic solvents [b] use of our products outdoors or in places where the products are exposed to direct sunlight or dust [c] use of our products in places where the products ar e exposed to sea wind or corrosive gases, including cl 2 , h 2 s, nh 3 , so 2 , and no 2 [d] use of our products in places where the products are exposed to static electricity or electromagnetic waves [e] use of our products in proximity to heat-producing components, plastic cords, or other flammable items [f] sealing or coating our products with resin or other coating materials [g] use of our products without cleaning residue of flux (ev en if you use no-clean type fluxes, cleaning residue of flux is recommended); or washing our products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] use of the products in places subject to dew condensation 4. the products are not subjec t to radiation-proof design. 5. please verify and confirm characteristics of the final or mounted products in using the products. 6. in particular, if a transient load (a large amount of load applied in a short per iod of time, such as pulse. is applied, confirmation of performance characteristics after on-boar d mounting is strongly recomm ended. avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading c ondition may negatively affect product performance and reliability. 7. de-rate power dissipation (pd) depending on ambient temper ature (ta). when used in seal ed area, confirm the actual ambient temperature. 8. confirm that operation temperat ure is within the specified range described in the product specification. 9. rohm shall not be in any way responsible or liable for fa ilure induced under deviant condi tion from what is defined in this document. precaution for mounting / circuit board design 1. when a highly active halogenous (chlori ne, bromine, etc.) flux is used, the resi due of flux may negatively affect product performance and reliability. 2. in principle, the reflow soldering method must be used; if flow soldering met hod is preferred, please consult with the rohm representative in advance. for details, please refer to rohm mounting specification downloaded from: http:///
datasheet d a t a s h e e t notice - ge rev.002 ? 2014 rohm co., ltd. all rights reserved. precautions regarding application examples and external circuits 1. if change is made to the constant of an external circuit, pl ease allow a sufficient margin considering variations of the characteristics of the products and external components, including transient characteri stics, as well as static characteristics. 2. you agree that application notes, re ference designs, and associated data and in formation contained in this document are presented only as guidance for products use. theref ore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. precaution for electrostatic this product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. please take proper caution in your manufacturing process and storage so that voltage exceeding t he products maximum rating will not be applied to products. please take special care under dry condit ion (e.g. grounding of human body / equipment / solder iron, isolation from charged objects, se tting of ionizer, friction prevention and temperature / humidity control). precaution for storage / transportation 1. product performance and soldered connections may deteriora te if the products are stor ed in the places where: [a] the products are exposed to sea winds or corros ive gases, including cl2, h2s, nh3, so2, and no2 [b] the temperature or humidity exceeds those recommended by rohm [c] the products are exposed to di rect sunshine or condensation [d] the products are exposed to high electrostatic 2. even under rohm recommended storage c ondition, solderability of products out of recommended storage time period may be degraded. it is strongly recommended to confirm sol derability before using products of which storage time is exceeding the recommended storage time period. 3. store / transport cartons in the co rrect direction, which is indicated on a carton with a symbol. otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. use products within the specified time after opening a humidity barrier bag. baking is required before using products of which storage time is exceeding the recommended storage time period. precaution for product label qr code printed on rohm products label is for rohms internal use only. precaution for disposition when disposing products please dispose them proper ly using an authorized industry waste company. precaution for foreign exchange and foreign trade act since our products might fall under cont rolled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with rohm representative in case of export. precaution regarding intellectual property rights 1. all information and data including but not limited to application example contained in this document is for reference only. rohm does not warrant that foregoi ng information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. rohm shall not be in any way responsible or liable for infringement of any intellectual property rights or ot her damages arising from use of such information or data.: 2. no license, expressly or implied, is granted hereby under any intellectual property rights or other rights of rohm or any third parties with respect to the information contained in this document. other precaution 1. this document may not be reprinted or reproduced, in whol e or in part, without prior written consent of rohm. 2. the products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of rohm. 3. in no event shall you use in any wa y whatsoever the products and the related technical information contained in the products or this document for any military purposes, incl uding but not limited to, the development of mass-destruction weapons. 4. the proper names of companies or products described in this document are trademarks or registered trademarks of rohm, its affiliated companies or third parties. downloaded from: http:///
datasheet datasheet notice C we rev.001 ? 2014 rohm co., ltd. all rights reserved. general precaution 1. before you use our pro ducts, you are requested to care fully read this document and fully understand its contents. rohm shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny rohms products against warning, caution or note contained in this document. 2. all information contained in this docume nt is current as of the issuing date and subj ec t to change without any prior notice. before purchasing or using rohms products, please confirm the la test information with a rohm sale s representative. 3. the information contained in this doc ument is provi ded on an as is basis and rohm does not warrant that all information contained in this document is accurate an d/or error-free. rohm shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. downloaded from: http:///